manualshive.com logo in svg

BRP Evinrude E-TEC Series, Руководство по обслуживанию, Страница: 136 / 342

Поделиться
Скачать
BRP Evinrude E-TEC Series Скачать руководство пользователя страница 136

134

FUEL SYSTEM

FUEL COMPONENT SERVICING

Crush Ring Replacement

Injector crush rings must be

replaced if injector is installed in a different
head or cylinder location.

Use Slide Hammer assembly, P/N 391008, with
Slide Hammer Adaptor kit, P/N 390898, to remove
injector from mounting cup.

Thread adaptor and stud into face of injector. Hold
mounting cup securely. Use slide hammer to sep-
arate injector from mount housing.

Remove adaptor from injector. Remove crush ring
and O-rings from injector. Inspect and clean injec-
tor filter. Install new crush ring and O-rings. Lubri-
cate O-rings with 

STP

 

†

 Oil Treatment

.

Install injector into mount housing. Press on injec-
tor face until injector seats in mount housing.

002345

1.

Adaptor

007424

NOTICE

1

1.

Crush ring

2.

O-rings

002317

007425

2

1

Содержание Evinrude E-TEC Series























































































































































































































































































































































Отзывы:

Нет отзывов