manualshive.com logo in svg

BRP Evinrude E-TEC Series, Руководство по обслуживанию, Страница: 130 / 342

Поделиться
Скачать
BRP Evinrude E-TEC Series Скачать руководство пользователя страница 130

128

FUEL SYSTEM

FUEL SYSTEM TESTS

Circulation Pump Resistance Test

Disconnect the battery cables at the battery.

Use a digital multimeter with appropriate adapter
leads to measure the fuel pump circuit and coil
resistance.

Lift Pump Pressure Test

Install a 0 to 15 psi (0 to 103 kPa)

 

Fuel Pressure

Gauge.

 

Tee into the fuel supply line before the fuel

filter.

Prime the fuel system and check for leaks. START
outboard and run at idle speed. Hold gauge level
with inlet fitting and monitor gauge for pressure
reading.

Pressure should stabilize at a reading greater
than 2 psi (14 kPa).

Results:

Normal pressure:

•

Perform the 

Lift Pump Vacuum Test

 on p. 129.

Make sure no air leaks or restrictions exist in
the fuel supply hose or boat fuel system.

Low pressure:

•

Check pulse hoses and fittings for restrictions.

•

Perform the 

Lift Pump Vacuum Test

 on p. 129.

Make sure no air leaks or restrictions exist in
the fuel supply hose or boat fuel system.

•

Check fuel flow through fuel lift pump. Use fuel
primer bulb to force fuel through pump.

No pressure:

•

Check pulse hoses and fittings restrictions.

•

Check fuel flow through fuel lift pump. Use fuel
primer or primer bulb to force fuel through
pump.

•

Momentarily prime or squeeze primer bulb to
check gauge operation.

•

Check pulse hose and fittings for restrictions.

Fuel Pump Resistance

2 to 8 

 @ 77°F (25°C) 

007417

1.

Fuel pressure gauge

2.

Tee fitting

007418

1

2

Содержание Evinrude E-TEC Series























































































































































































































































































































































Отзывы:

Нет отзывов