manualshive.com logo in svg

BRP Evinrude E-TEC Series, Руководство по обслуживанию, Страница: 126 / 342

Поделиться
Скачать
BRP Evinrude E-TEC Series Скачать руководство пользователя страница 126

124

FUEL SYSTEM

COMPONENTS

Fuel Manifold

The vapor separator uses molded internal pas-
sages to route fuel directly to and from the injec-
tors. Refer to 

FUEL SYSTEM HOSE ROUTING

on p. 118.

Fuel Injectors

Fuel injectors are fuel metering, electric solenoids
(55 V) bolted directly to the cylinder head. The

EMM

 controls the activation of each injector by

rapidly connecting and disconnecting the injec-
tor’s internal coil to ground.

Fuel Flow Compensation

The flow rate of each injector is measured as part
of the manufacturing process. This information is
recorded and assigned to the injector by serial
number.

The 

EMM

 is programmed to compensate for vari-

ations in fuel flow. Each injector and its location on
the outboard is identified by the 

EMM

. DO NOT

install an injector without updating the compensa-
tion software.

Each service injector includes its fuel flow infor-
mation on a 3.5 in. floppy disk. This software
allows the 

EMM

 to be reprogrammed for this injec-

tor’s unique fuel flow characteristics.

Fuel injectors MUST NOT be moved

from one cylinder to another. EMM program-
ming is associated with the cylinder location
of each injector. Installing an injector on the
wrong cylinder can result in powerhead fail-
ure.

Injector Fuel Supply

Fuel is supplied to the injectors by the fuel circula-
tion pump and the fuel supply manifold.

Each injector has internal fuel passages. These
passages are designed to:

•

Provide fuel to the injector's injection chamber

•

Route fuel through the injector housing to cool
the injector coil and armature

006619

NOTICE

Содержание Evinrude E-TEC Series























































































































































































































































































































































Отзывы:

Нет отзывов