manualshive.com logo in svg

BRP Evinrude E-TEC Series, Руководство по обслуживанию, Страница: 110 / 342

Поделиться
Скачать
BRP Evinrude E-TEC Series Скачать руководство пользователя страница 110

108

ELECTRICAL AND IGNITION

ELECTRIC STARTER SERVICING

Remove brush holder cap from armature and
frame assembly. Do not lose the brush springs.

Slowly, remove the armature from frame.

Starter Cleaning and Inspection

Inspect the brushes for wear and damage.
Replace brushes if damaged or worn. Replace
weak brush springs.

Clean the commutator with 300-grade emery
cloth. If commutator surface is unevenly worn or
pitted, turn it on a lathe. Remove any trace of oil or
metal dust from commutator.

Check the armature on a growler for shorted turns
using a test light or meter. Inspect armature insu-
lation for indications of overheating or damaged
windings. Clean off any carbon deposits or foreign
matter which could contribute to failure of wind-
ings.

Check permanent magnets and make sure they
strongly attract any steel or iron object held inside
frame. Weak magnetism could cause excessive
RPM on 

No Load Current Draw Test

 on p. 97.

After disassembling the drive, clean each part with

Cleaning Solvent

 and inspect for wear and distor-

tion.

002299

38288

002301

TYPICAL

24058

TYPICAL

24057

Содержание Evinrude E-TEC Series























































































































































































































































































































































Отзывы:

Нет отзывов