BRP Evinrude E-TEC Series Скачать руководство пользователя страница 109 | Manualshive

Страница: 109 / 342

BRP Evinrude E-TEC Series Скачать руководство пользователя страница 109

107

ELECTRICAL AND IGNITION

ELECTRIC STARTER SERVICING

6

ELECTRIC STARTER
SERVICING

Starter Removal

IMPORTANT:

Do not clean the starter drive

while the starter motor and drive are installed on
the powerhead. The cleaning agent could drain
into the starter motor, washing dirt from the drive
into the starter bearings and commutator.

Disconnect the battery cables at the battery.

Remove lower motor covers. Refer to

Cover Removal

Remove the starter positive (+) cable from post on
starter.

Remove three starter mounting screws. Remove
the starter.

Starter Disassembly

Remove the retaining nut, spacers, spring and
starter pinion from pinion shaft.

Mark the end cap and brush holder cap orienta-
tion. Remove the two thru-bolts.

Remove the end cap and thrust washer.

1.

Screws

007253

1

1

007438
007439

002296

002298

«
...
107
108
109
110
111
...
»

Содержание Evinrude E-TEC Series























































































































































































































































































































































Отзывы:

Нет отзывов