manualshive.com logo in svg

BRP Evinrude E-TEC Series, Руководство по обслуживанию, Страница: 102 / 342

Поделиться
Скачать
BRP Evinrude E-TEC Series Скачать руководство пользователя страница 102

100

ELECTRICAL AND IGNITION

TILT/TRIM RELAY TEST

TILT/TRIM RELAY TEST

The tilt and trim (TNT) module contains the cir-
cuitry and relays required for power trim and tilt
operation.

The tilt and trim switch provides B+ input to
green/white or blue/white wire of the TNT module.

Operation

The relay activates when B+ input from the switch
is supplied to terminal 86 of the internal relays. 

Terminal 87a connects to ground (B–).

Terminal 87 connects to B+.

Terminal 30 connects TNT motor.

Terminals 87a and 30 are connected when relay is
not activated. This supplies ground (B–) connec-
tion to TNT motor.

Terminals 87 and 30 are normally open. B+ is
applied to terminal 30 when relay is activated.
This supplies ground B+ connection to TNT motor.

Refer to 

Tilt and Trim Module Diagram

.

Test Procedure

Make sure red and black wires are connected to
12 V battery power supply. 

Set voltmeter to 12 VDC scale. Connect test leads
to terminals “A” and “B” of TNT motor connector. 

Use a wire jumper to alternately connect B+ to ter-
minals “1” and “2” of tilt and trim switch connector.

The meter must indicate battery voltage (12 V)
with B+ connected to either terminal.

1.

Tilt and trim module

007356

1

Tilt and Trim Module Diagram
1.

Green/white wire

2.

Blue/white wire

3.

B+, red wire

4.

B–, black wire

5.

TNT motor connector

6.

TNT switch connector

002063

3

4

1

2

6

5

Содержание Evinrude E-TEC Series























































































































































































































































































































































Отзывы:

Нет отзывов