manualshive.com logo in svg

BRP Can-Am Spyder RS 2014 Series, Бюллетень предварительной поставки

Поделиться
Скачать
BRP Can-Am Spyder RS 2014 Series Скачать руководство пользователя страница 32

SETUP

A

B

1

C

D

rmo2008-027-105_b

HEADLIGHT REFLECTION ON TEST SURFACE — HIGH BEAM

1. Focus point

A. 828 mm (32-19/32 in) above ground
B. 738 mm (29-1/16 in) above ground
C. 464 mm (18-9/32 in) above ground
D. 374 mm (14-23/32 in) above ground

Select low beam.

Beam aiming is correct when the focus point
(brightest point) of headlight reflection is be-
tween lower marks.

rmo2014-002-001_a

HEADLIGHT REFLECTION ON TEST SURFACE — LOW BEAM

1. Focus point

A. 828 mm (32-19/32 in) above ground
B. 738 mm (29-1/16 in) above ground
C. 464 mm (18-9/32 in) above ground
D. 374 mm (14-23/32 in) above ground

NOTE:

For LH traffic country application, low

beam headlights must have been replaced as
described in this predelivery bulletin.

High Beam

Turn adjustment screws to adjust beam height.
Adjust both headlights evenly.

rmr2008-027-102_a

ADJUSTMENT SCREWS

Low Beam

Insert a long Phillips screwdriver into air duct to
reach the adjustment screws.

rmr2008-027-106_a

1. Air duct
2. Screwdriver

Turn adjustment screws to adjust beam height.
Adjust both headlights evenly.

B.U.D.S. Programming

Always use the latest B.U.D.S. version on your
shop computer. It is available from the following
web site:

WWW.BOSSWEB.BRP.COM

Please note that the latest B.U.D.S. version is also
available in Info Center.

NOTICE

During data transfer, make sure that:

– Voltage (12V) remains stable before starting

update. Charge the battery or use a power
pack to ensure sufficient power reserve for
the procedure.

– Although the screen may ''freeze'' for a

while, B.U.D.S. continues to function in the
background.

– Never disconnect any cable while updating

the ECM.

MANDATORY TOOLS

A personal computer (laptop or desktop)

MPI-2 INTERFACE CARD
(P/N 529 036 018)

MPI-2 DIAGNOSTIC CABLE
(P/N 710 000 851)

OPTIONAL TOOL

Extension cable
available at electronic retail outlets.
Do not exceed 7.5 m (25 ft)

32 / 39

2014-2

PREDELIVERY

Содержание Can-Am Spyder RS 2014 Series








































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды