manualshive.com logo in svg

BRP Can-Am Spyder RS 2014 Series, Бюллетень предварительной поставки

Поделиться
Скачать
BRP Can-Am Spyder RS 2014 Series Скачать руководство пользователя страница 20

PARTS TO BE INSTALLED

7. Ensure harness brackets are properly posi-

tioned when torque is applied.

8. Ensure cap for wheel hub nut is properly se-

cured to steering knuckle.

rbl2014-004-050_a

TYPICAL

1. Check for harness bracket contact here
2. Wheel hub nut cap secure

9. Remove protection from suspension arms.

Rear Fender

NOTE:

Before applying any torque, install all nuts

and screws.

1. Remove rear fender packaging.

2. Loosen LH and RH fender support screws.

rbl2013-002-012_a

LEFT SIDE FENDER SUPPORT

1. Screws, washers and nuts

3. Pre-assemble rear fender to its LH and RH rear

fender brackets with M6 x 12 screws, flat plas-
tic washers and M6 nuts (on back side).

rbl2013-002-013_a

1. Rear fender
2. Support
3. M6 x 12 Screws, washers and nuts

NOTE:

Do not torque screws.

4. Connect license plate light connector.

5. Secure license plate light harness inside RH

rear fender support using 4 locking ties (from
PDI kit) into factory installed retainers.

rbl2013-002-010_a

1. License plate light harness
2. Rear fender support
3. Locking ties in retainers

20 / 39

2014-2

PREDELIVERY

Содержание Can-Am Spyder RS 2014 Series








































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды