manualshive.com logo in svg

BRP Can-Am Spyder RS 2014 Series, Бюллетень предварительной поставки

Поделиться
Скачать
BRP Can-Am Spyder RS 2014 Series Скачать руководство пользователя страница 15

PARTS TO BE INSTALLED

7. Position battery retaining bracket over battery.

Be sure to properly engage it in the frame front
member.

8. Install rubber retaining strap.

rbl2013-003-014_a

1. Battery
2. Retaining bracket
3. Rubber strap
4. Hook on lower front frame member

AAPTS (Ambient Air Pressure
and Temperature Sensor)
Installation

1. Connect AAPTS connector and route cable

through retaining guide clips (RH side of cargo
module).

rbl2013-002-003_a

1. Cable retaining clip
2. Connector

Low Beam Headlight
Connection

Models with Low Beam Headlights
Mounted in Cargo Module

1. Connect wiring harness to low beam head-

lights.

rbl2008-003-215_b

1. Low beam headlight connector

Horn Connection

1. Connect horn connector.

2. Route cable through the retaining guide clips

(LH side of cargo module).

rbl2013-002-007_a

1. Horn connector

Models with Low Beam Headlights
Mounted in Cargo Module

If necessary, remove horn from vehicle to ease
connector installation.

PREDELIVERY

2014-2

15 / 39

Содержание Can-Am Spyder RS 2014 Series








































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды