background image

MAINTENANCE PROCEDURES

tmo2011-001-127_a

REAR OF VEHICLE

1. Outer drive shaft boot

Tightening Rear Stabilizer
Bar Bolts

Torque retaining screws of stabilizer
bar according to the following se-
quence.

tmr2011-036-004_b

STABILIZER BAR TIGHTENING SEQUENCE

TIGHTENING TORQUE

Stabilizer bar

screws

85 N•m ± 10 N•m

(63 lbf•ft ± 7 lbf•ft)

Wheel Bearing

Wheel Bearing Inspection

Lift and support vehicle. Refer to

LIFT-

ING AND SUPPORTING THE VEHICLE

in

VEHICLE INFORMATION SECTION

.

Push and pull the wheels from the up-
per edge to feel the play.

See an authorized Can-Am dealer if
there is any play.

tmo2011-001-131_a

TYPICAL

Wheels and Tires

Wheel Removal

Loosen nuts then lift and support vehi-
cle. Refer to

LIFTING AND SUPPORT-

ING VEHICLE

in

VEHICLE INFORMA-

TION

.

Remove nuts then remove wheel.

Wheel Installation

At installation, it is recommended to
apply anti-seize lubricant on threads.

The tires are unidirectional and their ro-
tation must be kept in a specific direc-
tion for proper operation.

Torque wheel nuts in accordance with
the following illustration.

TORQUE

Wheel lug nuts

100 N•m ± 10 N•m

(74 lbf•ft ± 7 lbf•ft)

______________

113

Содержание can-am COMMANDER 1000 2017




























































































































































Отзывы: