BRP can-am COMMANDER 1000 2017 Скачать руководство пользователя

Страница: 114 / 155

MAINTENANCE PROCEDURES

tmo2011-001-116_a

1. Tail light
2. Light bulb and socket

Push the bulb in and hold while turning
counterclockwise to release.

Installation is the reverse of the re-
moval procedure.

Position Lights Bulbs Replacement

Pull bulb out.

Installation is the reverse of removal.

Drive Shaft Boot and
Protector

Drive Shaft Boot and Protector
Inspection

Visually inspect drive shaft protectors
and boots conditions.

Check protectors for damage or rub-
bing against shafts.

Check boots for cracks, tears, leaking
grease, etc.

Repair or replace damaged parts as
necessary.

tmo2011-001-129_a

FRONT OF VEHICLE

1. Radiator
2. Inner drive shaft boots

tmo2011-001-130_a

FRONT OF VEHICLE

1. Outer drive shaft boot

tmo2011-001-128_a

REAR OF VEHICLE

1. Inner drive shaft boot

112

______________

Содержание can-am COMMANDER 1000 2017




























































































































































Результаты поиска

Содержание can-am COMMANDER 1000 2017

Отзывы:

Похожие инструкции для can-am COMMANDER 1000 2017

Бренды по названию

Популярные бренды

BRP can-am COMMANDER 1000 2017, Руководство оператора

Результаты поиска

Содержание can-am COMMANDER 1000 2017

Отзывы:

Похожие инструкции для can-am COMMANDER 1000 2017

Бренды по названию

Популярные бренды