Brother ScanNCut DX Скачать руководство пользователя | Manualshive

Страница: 31 / 38

background image

30

When Material Has Become Jammed in the
Machine

a

Press

in the operation panel to turn off the machine.

b

Unplug the power cord from the electrical outlet.

c

Remove the base attachment from the shaft.

a

Base attachment

d

Pull the feeder release lever (on the right side of the
machine) toward you.

a

Feeder release lever



Only the right side of the shaft is raised, and the shaft is
unlocked. This allows jammed material to easily be removed.

e

Remove any jammed material.

• Slowly pull out the material. Otherwise, internal machine parts

may be damaged.

Note

•

If material gets under the carriage and cannot be removed,
make sure that the machine is turned off, remove the
holder from the carriage, and then slowly move the
carriage by hand to remove the material.

f

Return the feeder release lever (on the right side of the
machine) to its original position.

a

Feeder release lever



Only the right side of the shaft is lowered, and the shaft is
locked.

g

Install the base attachment onto the shaft.

h

Insert the plug of the power cord into an electrical outlet.

i

Press

in the operation panel.

When the opening screen appears, touch anywhere on the
display.

1

1

1

«
...
29
30
31
32
33
...
»

Содержание ScanNCut DX







































Отзывы:

Нет отзывов

Похожие инструкции для ScanNCut DX

image Prograf iPF780 Series

Бренд: Canon Страницы: 326

imagePROGRAF TM Series

Бренд: Canon Страницы: 51

Бренд: Richpeace Страницы: 65

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды