Brother NC-150h Скачать руководство пользователя | Manualshive

Страница: 116 / 130

background image

Appendix A

110

A

Using APIPA to configure the IP address

A

The Brother print server supports the Automatic Private IP Addressing (APIPA) protocol. With APIPA, DHCP
clients automatically configure an IP address and subnet mask when a DHCP server is not available. The
device chooses it's own IP address in the range 169.254.1.0 through to 169.254.254.255. The subnet mask
is automatically set to 255.255.0.0 and the gateway address is set to 0.0.0.0.
By default, the APIPA protocol is enabled. If you want to disable the APIPA protocol, you can disable it using
control panel of the machine. For more information, see

If the APIPA protocol is disabled, the default IP address of a Brother print server is 192.0.0.192. However,
you can easily change this IP address number to match with the IP address details of your network.

Using ARP to configure the IP address

A

If you are unable to use the BRAdmin application and your network does not use a DHCP server, you can
also use the ARP command. The ARP command is available on Windows

®

systems that have TCP/IP

installed as well as UNIX

®

systems. To use arp enter the following command at the command prompt:

arp -s ipaddress ethernetaddress

Where

ethernetaddress

is the Ethernet address (MAC address) of the print server and

ipaddress

is the

IP address of the print server. For example:

Windows

®

systems

Windows

®

systems require the dash “-” character between each digit of the Ethernet address.

arp -s 192.168.1.2 00-80-77-31-01-07

UNIX

®

/Linux systems

Typically, UNIX

®

and Linux systems require the colon “:” character between each digit of the Ethernet

address.

arp -s 192.168.1.2 00:80:77:31:01:07

Note

You must be on the same Ethernet segment (that is, there cannot be a router between the print server and
operating system) to use the arp -s command.
If there is a router, you may use BOOTP or other methods described in this chapter to enter the IP
address.If your Administrator has configured the system to deliver IP addresses using BOOTP, DHCP or
RARP your Brother print server can receive an IP address from any one of these IP address allocation
systems. In which case, you will not need to use the ARP command. The ARP command only works once.
For security reasons, once you have successfully configured the IP address of a Brother print server using
the ARP command, you cannot use the ARP command again to change the address. The print server will
ignore any attempts to do this. If you wish to change the IP address again, use a web browser, TELNET
(using the SET IP ADDRESS command) or factory reset the print server (which will then allow you to use
the ARP command again).
To configure the print server and to verify the connection, enter the following command

ping ipaddress

where

ipaddress

is the IP address of the print server. For example,

ping 192.189.207.2

.

«
...
114
115
116
117
118
...
»

Содержание NC-150h



































































































































Отзывы:

Нет отзывов

Похожие инструкции для NC-150h

Бренд: QMS Страницы: 86

Бренд: Panasonic Страницы: 31

Бренд: QMS Страницы: 26

Бренд: Oki Страницы: 222

Бренд: Oki Страницы: 4

Бренд: Oki Страницы: 160

Magicolor 2 Desklaser

Бренд: QMS Страницы: 60

Бренд: Lanner Страницы: 43

Бренд: Olympus Страницы: 28

SuperServer 5013C-MT

Бренд: Supero Страницы: 98

Бренд: IESC Страницы: 109

Бренд: Oki Страницы: 255

Бренд: MAC TOOLS Страницы: 2

Bull Escala E5-700

Бренд: IBM Страницы: 116

Бренд: TYANO Страницы: 68

Бренд: Artesyn Страницы: 190

MediaGrid ContentServer 3000

Бренд: Omneon Страницы: 2

FlexWATCH 1110L

Бренд: Seyeon Technology Страницы: 96

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды