Brother MFC 5890CN - Color Inkjet - All-in-One Скачать руководство пользователя страница 147

Страница: 147 / 448

4-49

Confidential

[ 5 ] Sheet feeder (SF) mechanism

[ 6 ] Paper feeding mechanism

[ 7 ] Speaker

Defective component

Result

Error codes

Bank ASSY
(shown on

page 4-42

)

- Two or more sheets of paper will be fed at once.
- No paper will be fed.

82, 83, 88

Defective component

Result

Error codes

Paper feed roller
Paper ejection roller
(If the paper feed roller or
paper ejection roller is
defective, it is necessary
to replace the engine
unit.)

- Any of the following images may appear on the printout: ---

PF encoder disk
PF encoder sensor

- The following image may appear on the printout:

---

Defective component

Result

Error codes

Speaker

- No key clicks will be heard.
- The ringer will not sound.
- No tone will be transmitted.

---

VWXYZ

Содержание MFC 5890CN - Color Inkjet - All-in-One

































































































































































































































































































































































































































































Результаты поиска

Содержание MFC 5890CN - Color Inkjet - All-in-One

Отзывы:

Бренды по названию

Популярные бренды

Brother MFC 5890CN - Color Inkjet - All-in-One, Руководство по обслуживанию

Результаты поиска

Содержание MFC 5890CN - Color Inkjet - All-in-One

Отзывы:

Бренды по названию

Популярные бренды