Brother HS-3000 Скачать руководство пользователя страница 127 | Manualshive

Страница: 127 / 164

Brother HS-3000 Скачать руководство пользователя страница 127

5 - 4

Failure Investigation
for Electronic Parts

Pulse motors do not return to starting position

When the power is turned ON, the pulse motors do not return to the starting
position.
• When needle is up : Z pulse motor returns to it's starting position.
• When needle is down : F pulse motor returns to it's starting position.

N

Y

Is the resistance between the 1 & 2
pins and 3 & 4 pins on the pulse
motor connectors 6.7-7.7

Ω

?

N

Replace the ZPM lead wire assy.

Replace the pulse motor.

N

Y

When the Z pulse motor does not
return to starting point, is the resistance
between the pins 1 & 4, 2 & 3, 3 & 2
and 4 & 1 at the ZPM lead wire assy.
1

Ω

or less?

Y

Replace the FPM lead wire assy.

When the F pulse motor does not
return to starting point, is the resistance
between the pins 1 & 4, 2 & 3, 3 & 2
and 4 & 1 at the FPM lead wire assy.
1

Ω

or less?

Replace the main PCB assy.

«
...
125
126
127
128
129
...
»

Содержание HS-3000





































































































































































Отзывы:

Нет отзывов