Brother HS-3000 Скачать руководство пользователя страница 111

Страница: 111 / 164

4 - 10

Adjustment

Needle bar height

1. Attach the front cover assy..

2. Remove the presser foot, the needle plate B and the needle plate A, and then remove the inner rotary hook.

3. Start the test mode.

4. Select the pattern number "02" (3-point needle drop mode).

5. Move the needle to the left with the

(Reverse stitch button), and then turn the power off.

6. Turn the pulley by hand until the right edge of the needle aligns with the outer rotary hook point.

7. Loosen the socket set screw (FT, M4 x 4) in the needle bar block.

8. Move the needle bar up and down, and adjust clearance between the upper edge of the needle eye and the outer

rotary hook point to 1.0 to 1.4mm.

NOTE

• Check the socket set screw (FT, M4 x 4) faces front.

9. Tighten the socket set screw (FT, M4 x 4) of the needle bar block.

*Key point

• Need to adjust “4-12 Needle threader” after this adjustment.

Socket set screw
(FT, M4 x 4)

Needle bar block

Needle bar

1.0 - 1.4mm

The right edge of the needle is aligned
with the tip of the outer rotary hook.

Содержание HS-3000





































































































































































Результаты поиска

Содержание HS-3000

Отзывы:

Brother HS-3000, Руководство по обслуживанию, Страница: 111 / 164

Результаты поиска

Содержание HS-3000

Отзывы: