manualshive.com logo in svg

Brother HL-5580D, Руководство по обслуживанию

Поделиться
Скачать
Brother HL-5580D Скачать руководство пользователя страница 46

2-20

Confidential

3.2 Error Messages

3.2.1 Non touch panel models

First line

Scroll

Description

Error 

codes

Refer 

to:

Cartridge Error

Put the Toner 
Cartridge back in.

The new toner sensor could not 
detect the new toner cartridge 
correctly.

4F01

2-50

Cooling Down

Wait for a while

The side thermistor of the fuser 
unit or internal temperature sensor 
detected a temperature higher 
than the specified value.

6801

2-53

Cover is Open

Close the Back Cover 
of the machine.

The eject sensor detected that the 
fuser cover was open.

6004

2-52

Close the Front Cover. The front cover sensor detected 

that the front cover was open.

6001

2-51

Drum !

Slide the Green tab on 
Drum Unit.

Detected discharge that may be 
attributable to dirty corona wire on 
the drum unit.

6A00

2-54

Drum End Soon

-

The number of rotations of the 
drum unit is reaching the upper 
limit.

4000

2-49

Ignore Data

-

Detected undecodable data during 
printing. Received undecodable 
PS data.

---

4.11.1

Jam 2-sided

Pull out the Duplex 
Tray at the back of the 
machine and remove 
the jammed paper.

The registration front sensor does 
not detect paper pass within the 
specified time after the first side 
was printed in duplex printing 
mode.

7800

2-66

Jam Inside

Open the Front Cover, 
pull out the Drum Unit 
completely and 
remove the jammed 
paper.

The eject sensor does not detect 
paper pass after the registration 
rear sensor detected the paper 
pass.

7000

2-55

Jam MP Tray

Remove the jammed 
paper from MP Tray 
and press Go.

When feeding from the MP tray, 
the registration rear sensor does 
not detect paper pass within the 
specified time after the registration 
front sensor detected paper pass.

7200

2-56

Jam Rear

Open the Back Cover 
and remove the 
jammed paper.

The eject sensor remains ON 
(paper pass detected) even after 
the registration rear sensor 
detected the end of paper pass.

7100

2-56

Jam Tray 1

Remove the jammed 
paper from Tray 1.

When printing from the paper tray 
1, the registration front sensor 
does not detect paper pass within 
the specified time after the T1 
paper feed sensor detected paper 
pass.

7302

2-57

Содержание HL-5580D


















































































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды