manualshive.com logo in svg

Brother HL-5580D, Руководство по обслуживанию, Страница: 364 / 433

Поделиться
Скачать
Brother HL-5580D Скачать руководство пользователя страница 364

5-15

Confidential

1.3.8 Check sensor operation (function code: 32)

<Function>

This function is used to check whether the sensors, solenoids, and clutches are operating normally.

<Operating Procedure>

<Sensor check>

The table below summarizes the displays on the LCD, sensor names and detection status.

LCD

Sensor name

Detection status

With display

No display

TN

Toner amount detection sensor

Beam obstructed

Beam not obstructed

NT

New toner sensor

Sensor not pressed

Sensor pressed

ST

Output tray stack sensor

Ejected paper not yet full Ejected paper full

C2

T2LT Paper feed sensor

Paper tray 2 closed

Paper tray 2 open

P2

T2LT paper empty sensor

No paper

Paper set

MC

MX back cover sensor

MX back cover closed

MX back cover open

TT

TT connection sensor

TT connected

TT not connected

Non touch panel models

(1) Press the [

▲

] or [

▼

] key in the initial 

state of maintenance mode to display 
"MAINTENANCE 32" on the LCD, and 
press the [OK] key. "TNNT--C2P2****" is 
displayed on the LCD. The machine 
makes buzzing sound continuously.
Information related to the LT, TT, and MX 
are not displayed on the LCD when 
those are not connected.

(2) Pressing the [Go] key changes the 

display to the next item.

(3) Change the conditions subject to sensor 

detection shown below and check that 
the display on the LCD changes 
depending on the sensor status. For 
example, feed the paper through the 
registration front/rear sensor, open the 
front cover or back cover, remove the 
toner cartridge, or create paper jam at 
the exit.

(4) When you press the [X] key, this 

operation is finished and the machine 
returns to the initial state of maintenance 
mode.

Touch panel models

(1) Press the [3], and then the [2] key in the 

initial state of maintenance mode. Either 
of the following examples is displayed 
on the LCD
e.g. TNNTSTC2P2**TT**
e.g. TNNTST----MCTT
The machine makes buzzing sound 
continuously.
Information related to the LT, TT, and MX 
are not displayed on the LCD when 
those are not connected.

(2) Pressing the [Mono] key changes the 

display to the next item.

(3) Change the conditions subject to sensor 

detection shown below and check that 
the display on the LCD changes 
depending on the sensor status. For 
example, feed the paper through the 
registration front/rear sensor, open the 
front cover or back cover, remove the 
toner cartridge, or create paper jam at 
the exit.

(4) When you press the [STOP] key, this 

operation is finished and the machine 
returns to the initial state of maintenance 
mode. 

Note: 

• Press the [OK] key to stop the 

buzzing sound.

Note: 

• Press the [SET] key to stop the 

buzzing sound.

Содержание HL-5580D


















































































































































































































































































































































































































































Отзывы:

Нет отзывов