manualshive.com logo in svg

Brother HL-5580D, Руководство по обслуживанию

Поделиться
Скачать
Brother HL-5580D Скачать руководство пользователя страница 334

4-3

Confidential

1.1.2 Installing firmware

<Operating Procedure>

■

Firmware installation using USB flash memory

(1) Create and save a file for automatic firmware update (file name: "_@$UPD$OP0.8080") 

under the USB flash memory.

(2) Create the "FIRM" folder under the USB flash memory, and save the program file 

needed for firmware install (ex: 1LINE: D001GJ_A.djf or D001GH_A.djf, Touch panel: 
D001GG_A.djf) in the "FIRM" folder.

(3) Connect the USB flash memory to the USB flash memory port at the side of the machine 

while the machine is in the ready state. "Program Updating.Do not turn off." appears on 
the LCD and installation starts automatically. Back light blinks during the installation.

(4) When installing is completed, the machine restarts automatically and "Completed..." 

appears on the LCD. Remove the USB flash memory. If multiple program files are saved 
in the USB flash memory, other installations start automatically after the restart.
If the installation fails, "Unable to Update:**" appears on the LCD. ("**" indicates the 
error code.) Refer to the remedy and eliminate the error. Then reboot the machine and 
start from the procedure (1).

Note:

• TT, MX, and LT have their own firmware respectively. They are included in the main 

firmware. When connecting the options to the machine and turning on the power 
switch, the firmwares of these options will be updated with the main firmware version 
of the machine. 

Memo:

• Do not disconnect the power cord, USB flash memory or USB cable from the machine 

or computer during installing.

• If the installation is failed, turn OFF the machine and turn it back on. The machine 

enters the firmware install mode automatically. Continue the operation procedure below. 

• Firmware installation using USB flash memory is inoperable when the machine is in 

deep sleep mode. Release the deep sleep mode by opening / closing the front cover 
before the operation.

• Be sure to reinstall the sub firmware and then the main firmware in this order.
• When the firmware installation using USB flash memory is failed and the error 

message or no character appears on the LCD, refer to 

“Firmware installation using 

PC” in this chapter

 to install firmware using PC.

Error display

Description

Remedy

Unable to Update:01 Memory full

(Failed to secure the work area for 
update.)

Delete some data saved in the 

machine and install again.

Unable to Update:02 No folder is specified

Save the firmware in the root 

folder (just below the USB 

flash memory).

Unable to Update:03 Specified folder does not have a file

Unable to Update:04 File access failure

Change the USB flash memory 

and install again.

Unable to Update:05 File data parsing error

Acquire the firmware from the 

data bank again.

Unable to Update:06 File name has exceeded the 

character limit

Shorten the file name to be 

less than 119 Byte.

Unable to Update:07 Unsupported DJF file detected

Acquire the firmware from the 

data bank again.

Unable to Update:08 Other function is in use

Perform it again after finishing 
the running function.

Содержание HL-5580D


















































































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды