Brother HL-5250DN series Скачать руководство пользователя

Страница: 164 / 337

CHAPTER 4 TROUBLESHOOTING

Confidential

4-50

(I-15) White spots

Possible cause

Step

Check

Result

Remedy

Are the white spot at 94.2mm
intervals?

Yes

1) If toner or glue remains

stuck, wipe it off gently with a
cotton swab. (Refer to

NOTE

in the next page.)

2) If the drum surface is

scratched, replace the drum
unit.

Drum unit failure

Is the problem solved after
replacing the drum unit?

Yes

Replace the drum unit.

No toner

Is the toner in the toner
cartridge almost empty?

Yes

Replace the toner cartridge with
a new one.

Print paper

Is the problem solved after
changing to specified freshly
unpacked paper?

Yes

Damp (wet) paper might be
used. Recommend to change
freshly unpacked paper.

Environment

Does the problem still appear
after the printer has warmed
up?

Yes

1) Replace the drum unit.
2) Advise the user of the

specified print environment.

User Check

(1) If the problem is not solved after printing a few pages, the drum unit may have

glue from label stock on the exposure drum surface. Refer to Step 1 in the table
below and

NOTE

in the next page.

(2) The drum unit may be damaged. Install a new drum unit.

Содержание HL-5250DN series


















































































































































































































































































































































Результаты поиска

Содержание HL-5250DN series

Отзывы:

Похожие инструкции для HL-5250DN series

Бренды по названию

Популярные бренды

Brother HL-5250DN series, Руководство по обслуживанию

Результаты поиска

Содержание HL-5250DN series

Отзывы:

Похожие инструкции для HL-5250DN series

Бренды по названию

Популярные бренды