manualshive.com logo in svg

Brother HL-5250DN series, Руководство по обслуживанию

Поделиться
Скачать
Brother HL-5250DN series Скачать руководство пользователя страница 120

CHAPTER 4 TROUBLESHOOTING 

Confidential 

4-6

2.1.2  Operator calls for HL-5270DN/5280DW 

An “Operator call” which the printer indicates on the LCD display is user recoverable.  Identify 
the error from the table below and take the corrective action described for each indication to 
correct it.  The printer automatically recovers from most errors.  If not, the error is cleared by 
holding down the 

Go

 button on the control panel. 

The LCD names for the paper trays are as follows. 

• 

Upper paper tray: 

TRAY 1

 

• 

Multi-purpose tray: 

MP

 

• 

Optional Lower tray: 

TRAY 2

 or 

TRAY 3

 

 

Error message 

Error message 

Remedy 

BUFFER ERROR 

Check the Interface settings. 

CARTRIDGE ERROR 

The drum unit ASSY is not installed in properly.  Take out the drum 
unit ASSY and put it back into the printer again.  

DIMM ERROR 

Re-installed the DIMM correctly.  Turn off the printer.  Wait a few 
seconds, and then turn it on again.  If this error message appears 
again, replace the DIMM with a new one.  

DOWNLOAD FULL 

Add more memory.  

DUPLEX DISABLED 

Close the back cover of the printer and put the duplex tray back in. 

Open the front cover.  Take out the drum unit and toner cartridge 
ASSY.  Gently slide the blue tab of the drum unit across several 
times. 

DUST ON DRUM 

Clean the electrodes of the main body and drum unit.  
(Refer to 

6.4 “Location of Ground Contacts”

 in this Chapter.) 

FONT FULL 

Add more memory. 

FRONT COVER OPEN 

Close the front cover of the printer. 

FUSER COVER OPEN 

Close the fuser cover located behind the back cover of the printer. 

 

Fig. 4-1 

JAM XXX 

Carefully pull out the jammed paper from the area shown in the 
“Paper jams and how to clear them” refer to

 3.2 “Paper Jams” in this 

Chapter.

 

MANUAL FEED 

Put the same size of paper in the MP tray as is shown on the LCD.  If 
the printer is “paused”, press the 

Go 

button. 

MEMORY FULL 

Add more memory. 

Содержание HL-5250DN series


















































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды