Brother HL-3040CN Скачать руководство пользователя страница 378

Страница: 378 / 437

7-24

Confidential

1.4.12 LED test pattern print (Function code 68)

<Function>

This function allows you to print the LED ASSY test pattern and check the quality of the LED
ASSY and if it is lifted from the drum.

<Operating procedure>

(1) Press the

button to display “MAINTENANCE 68” on the LCD in the initial state of

the maintenance mode. Then, press the

button.

(2) When “M68_L” is displayed on the LCD, press the

button.

The available test patterns are shown below.

“PRINTING” is displayed on the LCD, and the LED test pattern is printed on a sheet.

(3) Press the

Cancel

button to return to the machine to the initial state of the maintenance

mode.

When an error message is displayed on the LCD, take the measures described in the
table below.

* # indicates the toner color (K, Y, M, or C) of which cartridge became empty.

Note:

You can check scratches and smears on the LED by performing the continuous print test.
(Refer to

“1.4.11 Continuous print test (Function code 67)”

in this chapter.)

LCD

Description

M68_L

Vertical/horizontal dot loss check pattern

Note:

When printing fails, a relevant error is displayed on the LCD. When the error factors
are removed and the

button is pressed, the machine automatically recovers to the

re-executable state. “PRINTING” is displayed on the LCD, and the test pattern is
printed on a sheet.

Error message

Measure

TONER EMPTY # *

Replace the empty toner cartridge and press the

button to

clear the error. Perform the LED test pattern print again.

Cover is Open

Close the top cover.

No Paper

Replenish paper, and press the

button to clear the error.

Jam Tray1

Remove the jammed paper, and press the

button to clear

the error.

Jam Rear

Remove the jammed paper, and press the

button to clear

the error.

Содержание HL-3040CN






















































































































































































































































































































































































































































Результаты поиска

Содержание HL-3040CN

Отзывы:

Brother HL-3040CN, Руководство по обслуживанию, Страница: 378 / 437

Результаты поиска

Содержание HL-3040CN

Отзывы: