Brother HL-2150N Скачать руководство пользователя | Manualshive

Страница: 33 / 177

background image

1-18

Confidential

3.

PAPER FEEDING PROBLEMS

Problems related to paper feeding are end user recoverable if following the User Check
items. If the same problem occurs again, follow each procedure in the order of the number
described in the Step column in the tables below.

3.1

No Feeding

3.2

Double Feeding

Step

Cause

Check

Result

Remedy

1

Edge actuator
catching on some
position

Does the edge actuator
move smoothly?

No

Re-assembly the edge
actuator

2

Roller holder
ASSY catching on
some position

Does the roller holder
ASSY move smoothly?

Yes

Re-assembly the roller
holder ASSY.

3

Registration front
sensor failure

Is the problem solved
after replacing the
registration front sensor
PCB ASSY?

Yes

Replace the registration
front sensor PCB ASSY.

4

Paper feeding kit
failure

Is the surface of the
separation pad or the
pickup roller dirty or worn
out?

Yes

1) Clean the surface of

the separation pad or
pickup roller.

2) Replace the separation

pad or pickup roller.

5

Pressure plate
gear damage

Is the pressure plate gear
damaged?

Yes

Replace the paper tray.

6

T1 solenoid failure

Does the T1 solenoid
work correctly?

No

Replace the T1 solenoid

7

T1 solenoid
pathway of the
high-voltage
power supply PCB
broken

Is the problem solved
after replacing the high-
voltage power supply
PCB ASSY?

Yes

Replace the high-voltage
power supply PCB ASSY.

8

Main PCB failure

Is the problem solved
after replacing the main
PCB ASSY?

Yes

Replace the main PCB
ASSY.

9

Main motor failure

Is the problem solved
after replacing the drive
sub ASSY?

Yes

Replace the drive sub
ASSY.

Step

Cause

Check

Result

Remedy

1

Paper feeding kit
failure

Is the surface of the
separation pad worn out?

Yes

Replace the paper
feeding kit.

«
...
31
32
33
34
35
...
»

Содержание HL-2150N


















































































































































































Отзывы:

Нет отзывов

Похожие инструкции для HL-2150N

Бренд: Xerox Страницы: 168

Бренд: Xerox Страницы: 36

Бренд: Xerox Страницы: 64

Бренд: Xerox Страницы: 54

Бренд: Xerox Страницы: 2

Бренд: Xerox Страницы: 115

Бренд: Samsung Страницы: 82

Бренд: Samsung Страницы: 2

Бренд: Lanier Страницы: 265

Бренд: Oki Страницы: 116

Бренд: Oki Страницы: 52

Бренд: Oki Страницы: 331

Бренд: Oki Страницы: 36

C5800Ldn Series

Бренд: Oki Страницы: 143

Бренд: Oki Страницы: 101

Бренд: Oki Страницы: 36

Бренд: Oki Страницы: 282

Бренд: Oki Страницы: 269

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды