Brother HL-2150N Скачать руководство пользователя страница 25

Страница: 25 / 177

1-10

Confidential

Cartridge position error

Identification failure for a new toner cartridge.

No paper fed tray 1

No paper in Tray (T1)

User Check

• Install the toner cartridges into the machine properly.

Step

Cause

Remedy

Power off or front cover opened
while detecting a new toner
cartridge.

Reset the developing bias voltage and
develop roller counter. (Refer to

"Developer

Roller Counter Reset"

in Chapter 5.)

User Check

• Check if the paper is loaded into the paper tray correctly. Then press the [Go] button.

Step

Cause

Remedy

Registration front sensor failure

Check the sensor performance following
the procedure in

"Factory Inspection Mode"

(Chapter 5).
If any problem occurs, replace the
registration front sensor PCB ASSY.

Lift arm and roller holder ASSY not
assembled correctly

Be sure to put the boss of the roller holder
ASSY into the hole on the lift arm securely.

Harness connection failure of
registration front sensor PCB
ASSY

Check the harness connections of the
registration front sensor PCB ASSY, and
reconnect it.

Harness connection failure of T1
solenoid

Check the harness connections of the T1
solenoid, and reconnect it.

Plate-up function malfunction

Replace the paper tray.

Toner LED PCB ASSY failure

Replace the toner LED PCB ASSY.

Main PCB ASSY failure

Replace the main PCB ASSY.

Содержание HL-2150N


















































































































































































Результаты поиска

Содержание HL-2150N

Отзывы:

Похожие инструкции для HL-2150N

Бренды по названию

Популярные бренды

Brother HL-2150N, Руководство по обслуживанию

Результаты поиска

Содержание HL-2150N

Отзывы:

Похожие инструкции для HL-2150N

Бренды по названию

Популярные бренды