Brother DCP Series Скачать руководство пользователя страница 258

Страница: 258 / 309

5-36

Confidential

1.4.19 Move of the Head/Carriage Unit to the Adjustment Position (Maintenance mode 63)

<Function>

This function moves the Head/carriage unit to the adjustment position.

<Operating Procedure>

(1) Enter [6] and [3] in the initial stage of the maintenance mode.

The machine displays "SELECT 63?" on the LCD.

(2) Press [Mono Start].

The machine displays "START 63?" on the LCD.

(3) Enter [*].

The machine moves the Head/carriage unit to the adjustment position and displays
"HEAD ADJ" on the LCD.

(4) When finished making the change, press [Stop] or [X].

The Head/carriage unit returns to the home position and locks itself, then the machine
returns to the initial stage of the maintenance mode.

Содержание DCP Series






















































































































































































































































































































Результаты поиска

Содержание DCP Series

Отзывы:

Похожие инструкции для DCP Series

Бренды по названию

Популярные бренды

Brother DCP Series, Руководство по обслуживанию

Результаты поиска

Содержание DCP Series

Отзывы:

Похожие инструкции для DCP Series

Бренды по названию

Популярные бренды