Brother DCP Series Скачать руководство пользователя страница 235 | Manualshive

Страница: 235 / 309

background image

5-13

Confidential

1.4.4 ADF Performance Test (Maintenance mode 08) (For ADF Models Only)

<Function>

The function counts the documents fed by the automatic document feeder (ADF) and
displays the count on the LCD for checking the ADF performance.

<Operating Procedure>

(1) Set documents on the ADF unit.

The LCD continues to display "

■■

MAINTENANCE

■■■

".

(2) Enter [0] and [8] in the initial stage of the maintenance mode.

The machine feeds the documents in and out while counting them and displaying "ADF
CHECK P.**" on the LCD.
(** shows the current count.)

(3) Press [Stop] or [X] to return the machine to the initial stage of the maintenance mode.

Note

If no document is set on the ADF, the machine displays "NO DOCUMENT" on the
LCD and returns to the initial stage of the maintenance mode.

1.4.5 Printout of Test Pattern (Maintenance mode 09)

<Function>

This function prints out a test pattern (Print Quality Check sheet) to allow the service
personnel to check the print quality, together with the serial number.

If any print quality problem is found, use

"1.4.26 Purge Operation (Maintenance mode 76)"

in this chapter

to perform head cleaning.

<Operating Procedure>

(1) Enter [0] and [9] in the initial stage of the maintenance mode.

The machine displays "PRINTING" on the LCD and prints out a test pattern.
If no recording paper is loaded in the paper tray, printing will be canceled.

(2) Upon completion of printing, the machine returns to the initial stage of the maintenance

mode.

«
...
233
234
235
236
237
...
»

Содержание DCP Series






















































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для DCP Series

Бренд: LabelTac Страницы: 2

Бренд: Panasonic Страницы: 24

Бренд: Oki Страницы: 40

Workio DP-1820E

Бренд: Panasonic Страницы: 38

Бренд: Oki Страницы: 24

Бренд: Oki Страницы: 4

Бренд: Oki Страницы: 40

Бренд: Oki Страницы: 507

Бренд: Oki Страницы: 176

Бренд: Samsung Страницы: 351

Бренд: Samsung Страницы: 199

Бренд: Oki Страницы: 52

Бренд: Hanin Страницы: 27

Бренд: Canon Страницы: 65

Бренд: Sagem Страницы: 102

WorkCentre 3615DN

Бренд: Xerox Страницы: 4

VersaUV LEJ-640

Бренд: Roland Страницы: 321

BIZHUB 8050 CF5001

Бренд: Konica Minolta Страницы: 20

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды