Brother DCP Series Скачать руководство пользователя страница 173 | Manualshive

Страница: 173 / 309

background image

3-65

Confidential

9.11 Main PCB ASSY

Note

•

If you replace the Main PCB ASSY, you need to replace the Ink absorber box and
Flushing box, and the reset the purge and flushing counters.

•

Before starting work involving the Main PCB ASSY, make sure that the Power cord
and telephone line is unplugged from their outlets. There is a danger of electric
shock while working if you leave the Power cord or telephone line plugged.

•

Before removing the Main PCB ASSY, disconnect the harnesses and flat cables
first, then remove the screws. Also, before reinstalling the Main PCB ASSY,
tighten the screws first, then connect the harnesses and flat cables. Follow this
sequence while making sure that harnesses and flat cables are not damaged by
the screws and the screwdriver.

(1) Disconnect the following harnesses and flat cables from the Main PCB ASSY.

Note

•

Make sure that the Main PCB ASSY is screwed in place while connecting and
disconnecting harnesses and flat cables.

•

After disconnecting the flat cables, check that each cable is not damaged at its
end or short-circuited. Insert the flat cable straightly. After it is inserted, confirm
that the cable is not skewed.

(3_046L)

PF/Registration sensor

harness ASSY (7-wire)

Carriage flat cable 1

(14-wire)

Carriage flat cable 2

(9-wire)

Ink cartridge detection

sensor flat cable

(16-wire)

Modem PCB harness

(11-wire)

Ink cartridge

cover sensor harness

(2-wire)

Purge cam switch

harness (2-wire)

Speaker harness (2-wire)

Main PCB ASSY

Power supply harness

(6-wire)

Paper feed motor

harness (2-wire)

Carriage motor harness

(2-wire)

(USB interface)

CIS flat cable

(12-wire)

Scanner cover

open sensor

harness (2-wire)

Document scanning position sensor harness

(3-wire)

Document detection sensor

harness (3-wire)

Document scanner motor

harness (4-wire)

Panel harness

(6-wire)

ADF motor harness (4-wire)

«
...
171
172
173
174
175
...
»

Содержание DCP Series






















































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для DCP Series

Бренд: NCR Страницы: 10

Бренд: IBM Страницы: 334

Бренд: IBM Страницы: 428

Бренд: IBM Страницы: 316

Бренд: IBM Страницы: 210

ApeoSport C5540I

Бренд: Fuji Xerox Страницы: 108

Бренд: Lanier Страницы: 6

MP 2554SP Series

Бренд: Ricoh Страницы: 1

Бренд: Xerox Страницы: 85

ColourLaser 21 Series

Бренд: Xante Страницы: 32

Бренд: Lanier Страницы: 140

Бренд: DataCard Страницы: 106

IMAGERUNNER 7086

Бренд: Canon Страницы: 14

imageRUNNER 5055

Бренд: Canon Страницы: 4

imageRUNNER ADVANCE C2225

Бренд: Canon Страницы: 109

imageRUNNER ADVANCE 525 I

Бренд: Canon Страницы: 44

Бренд: Canon Страницы: 6

imageRUNNER ADVANCE C2020

Бренд: Canon Страницы: 48

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды