Brother DCP-J925DW Скачать руководство пользователя страница 334 | Manualshive

Страница: 334 / 378

Brother DCP-J925DW Скачать руководство пользователя страница 334

5-50

Confidential

1.4.24 Traveling Speed Check of Head/Carriage Unit

(Function code 69)

Function

This procedure checks whether the traveling speed of the head/carriage unit is within the
specified range.

Be sure to perform this procedure if you replace the head/carriage unit, carriage motor or CR
encoder strip, loosen the CR timing belt, or apply lubricant.

Operating Procedure

(1) Press the

6

and

9

keys in this order in the initial stage of the maintenance mode.

The machine shows "CR AGING" on the LCD and starts aging of the head/carriage unit.

In each of travel speeds of 57.7, 43.3, 26.7 and 21.7 inches/second (ips), the machine
checks whether the maximum and minimum traveling speeds of the head/carriage unit are
within the specified range.

- If the maximum and minimum speeds in all of the four traveling speeds are within the

specified range, the "57O 43O 27O 21O" appears on the LCD

- If any one is out of the range, the machine shows some message, e.g., "57O 43O 27O

21X" on the LCD. This sample message indicates that the speed variation is within the
allowable range when the head/carriage unit travels at 57.7, 43.3 and 26.7 inches/
second; however, it is out of the range at 21.7 inches/second.

(2) Press the

Stop/Exit

key to return the machine to the initial stage of the maintenance mode.

«
...
332
333
334
335
336
...
»

Содержание DCP-J925DW



























































































































































































































































































































































































Отзывы:

Нет отзывов