Brother DCP-J925DW Скачать руководство пользователя страница 231

Страница: 231 / 378

3-94

Confidential

(7) Release the three ink-related sensor flat cables from the cable guide (shown on

page 3-92

)

on the lower cover.

(8) Lift the ink refill ASSY up and out of the lower cover.

Note:

Do not remove the protective part under the current state. Doing so causes ink in the

ink supply tubes to flow out.

Note:

On the back of the ink refill ASSY is an ink absorber felt (for ink refill ASSY) that

may be stained with ink. If it is excessively stained, replace it.

(9) Remove the screw and take the ink cartridge detection sensor PCB up and off the ink refill

ASSY.

Assembling Note:

When replacing the ink cartridge detection sensor PCB ASSY, bend its flat

cable as specified below.

Taptite, cup B M3x8

Ink cartridge detection
sensor PCB

Ink refill ASSY

Protective part

Ink remaining sensor flat cable

High-yield ink cartridge sensor
flat cable

Ink cartridge detection sensor
flat cable

(3_085)

(3_085_1)

Reference

line

Conductor for

connection

UL symbol

print side

Valley fold, 180

Mountain fold, 180

Mountain fold,
180

Reference

line

Содержание DCP-J925DW



























































































































































































































































































































































































Результаты поиска

Содержание DCP-J925DW

Отзывы:

Похожие инструкции для DCP-J925DW

Бренды по названию

Популярные бренды

Brother DCP-J925DW, Руководство по обслуживанию

Результаты поиска

Содержание DCP-J925DW

Отзывы:

Похожие инструкции для DCP-J925DW

Бренды по названию

Популярные бренды