Brother DCP-J925DW Скачать руководство пользователя страница 102 | Manualshive

Страница: 102 / 378

Brother DCP-J925DW Скачать руководство пользователя страница 102

2-57

Confidential

4.2

Recording Paper or Disc Tray Feeding Problems

Problems related to recording paper or disc tray feeding are end user recoverable by following
the User Check items. If the problem persists, follow each procedure in the order of the number
described in the Step column in the tables below.

4.2.1 Recording paper not fed from paper tray

(Error code 18, 82, etc.)

User Check

- Check that recording paper is loaded correctly in the paper tray.

- Check that paper tray is set.

- Check that the jam clear cover is closed.

- Check that the recording paper weight is 64 to 120 g/m

2

.

- Check that the disc guide is closed.

- Clean the paper feed roller.

Step

Cause

Solution

1

ASF motor harness connection
failure

Check the connection and reconnect the harness.

2

Registration actuator defective

Check and reposition the registration actuator.

3

Paper tray defective

Replace the paper tray.

4

CR encoder strip stained

Replace the CR encoder strip.

5

Paper pull-in rollers worn out or
paper pull-in roller holder
defective

Replace the paper pull-in roller holder ASSY.

6

Registration sensor defective

Replace the registration sensor PCB ASSY.

7

ASF motor defective

Replace the ASF drive ASSY.

8

Engine unit defective

Replace the engine unit.

9

Main PCB defective

Replace the main PCB ASSY.

«
...
100
101
102
103
104
...
»

Содержание DCP-J925DW



























































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды