Brother DCP 7065DN Скачать руководство пользователя страница 124

Страница: 124 / 337

2-87

Confidential

■

White vertical streaks

■

White horizontal streaks

■

Faint print

User Check

• Check if there is no dust in the gap between the toner cartridge and

drum unit.

• Replace the toner cartridge with a new one.
• Check the machine's environment. High temperature and high

humidity or low temperature and low humidity conditions can cause
this problem.

• Damp (wet) paper might be used. Try to change to freshly

unpacked paper.

• Replace the drum unit with a new one.
• Leave the machine for a while as the power remains ON.

Step

Cause

Remedy

Laser unit failure

Replace the laser unit.

User Check

• This problem may disappear If print several sheets of page. Print

several sheets of page if the machine has not been used for a long
time.

• Replace the drum unit with a new one.
• Replace the toner cartridge with a new one.

Step

Cause

Remedy

Dirt on the electrodes of the drum

unit and the machine body

Clean the electrodes of the drum unit and

machine body. (Refer to

Fig. 2-11, Fig. 2-

12.

)

User Check

• Check that the machine is installed on a level surface.
• Replace the toner cartridge with a new one.

Step

Cause

Remedy

Main PCB failure

Replace the main PCB ASSY.

Laser unit failure

Replace the laser unit.

Fuser unit failure

Replace the fuser unit.

Содержание DCP 7065DN


















































































































































































































































































































































Результаты поиска

Содержание DCP 7065DN

Отзывы:

Бренды по названию

Популярные бренды

Brother DCP 7065DN, Руководство по обслуживанию

Результаты поиска

Содержание DCP 7065DN

Отзывы:

Бренды по названию

Популярные бренды