Brother 9500 - HL 1660EN B/W Laser Printer Скачать руководство пользователя

Страница: 87 / 258

USER’S GUIDE

4–20

FORMAT MODE

ORIENTATION

When you select “ORIENTATION”, you can set portrait or landscape
orientation.

✒

Note

The ORIENTATION selection is effective in the HP LaserJet, EPSON
FX-850, and IBM Proprinter XL modes. It does not work in other
emulation modes.

This printer can print pages in portrait or landscape orientation. You can
check the current orientation on the display.

Fig. 4-4 Page Orientation

When you enter the setting mode, the display first shows the current
orientation with an asterisk.

ORI=PORTRAIT *

Press the

▲

▼

switch until the desired orientation appears on the

display.

Display Message Orientation

ORI=PORTRAIT

Portrait

ORI=LANDSCAPE

Landscape

Press the SET switch to make the displayed selection effective.

An asterisk appears at the end of the display for a short time. Then the
printer automatically exits from the setting mode to the FORMAT
MODE.

PORTRAIT

LANDSCAPE

Содержание 9500 - HL 1660EN B/W Laser Printer



































































































































































































































































Результаты поиска

Содержание 9500 - HL 1660EN B/W Laser Printer

Отзывы:

Похожие инструкции для 9500 - HL 1660EN B/W Laser Printer

Бренды по названию

Популярные бренды

Brother 9500 - HL 1660EN B/W Laser Printer, Руководство пользователя

Результаты поиска

Содержание 9500 - HL 1660EN B/W Laser Printer

Отзывы:

Похожие инструкции для 9500 - HL 1660EN B/W Laser Printer

Бренды по названию

Популярные бренды