BRONKHORST ES-FLOW ES Series Скачать руководство пользователя

Страница: 46 / 55

Bronkhorst®

Instruction Manual ES-FLOW™

9.17.145E

Value

Description

No reset

Reset counter

Reset alarm

Reset counter

Reset and disable counter

Reset firmware program (soft reset)

Reset

Alarm info

error bit

Reset

Alarm info

warning bit

Reset totalizer

The

Reset

parameter may be disabled by

Reset Alarm Enable

Reset Counter Enable

. Make sure the value is accepted

by sending value 0 first.

Wink

Type

Access

Range

FlowDDE

FLOW-BUS

Modbus

Unsigned char [27]

0…9*

0/0

0x0000/1

Sending any text string value between 1 and 9 to this parameter makes the indication LEDs (if present) blink for a couple of

seconds. This can be useful in order to identify a specific device in a large fieldbus network.

*) Modbus only supports value 14592

Control Mode

Type

Access

Range

FlowDDE

FLOW-BUS

Modbus

Unsigned int

0…255

1/4

0x0024/37

Control Mode

is used to select different control modes of the instrument and determines from which source(s) it accepts a

setpoint. The following control modes are available:

Value

Mode

Instrument action

Setpoint source

BUS/RS-232

Controlling

Fieldbus/RS-232

Analog Input

Controlling

Analog input

FLOW-BUS Slave

Acting as slave instrument on FLOW-BUS

RS-485 only: FLOW-BUS

master output x

Slave

Factor/

100%

Valve Close

Controller disabled, valve closed

Controller Idle

Controller disabled, valve frozen in current position

Setpoint 100%

Controlling, setpoint fixed to 100%

Valve Fully Open

Controller disabled, valve fully opened

Calibration Mode Calibration mode enabled

(factory only)

Analog Slave

Acting as slave of other instrument in analog mode

Analog Input

Slave

Factor/

100%

Setpoint 0%

Controlling, setpoint fixed to 0%

FLOW-BUS

Analog Slave

Acting as slave of other instrument on FLOW-BUS, slave

factor is set by analog input signal

RS-485 only: FLOW-BUS

master output x

Analog Input

RS-232

Controlling, safe state deactivated

Fieldbus/RS-232

Valve Steering

Controller disabled, setpoint redirected to

Valve output

Analog Valve

Steering

Controller disabled, analog input redirected to

Valve output

Valve Safe State

Force instrument in safe state

Immediately after power-up,

Control Mode

is set to 'Analog input’ or ‘BUS/RS-232’ automatically, depending on the

(requested) default setting for analog or digital operation. If

Control mode

is set to value 0, 1, 9 or 18, the instrument returns

to its default control mode at the next power-up or reset. Other values are retained after power-up or reset.

Содержание ES-FLOW ES Series
























































Результаты поиска

Содержание ES-FLOW ES Series

Отзывы:

Похожие инструкции для ES-FLOW ES Series

Бренды по названию

Популярные бренды

BRONKHORST ES-FLOW ES Series, Инструкция по эксплуатации

Результаты поиска

Содержание ES-FLOW ES Series

Отзывы:

Похожие инструкции для ES-FLOW ES Series

Бренды по названию

Популярные бренды