BRONKHORST ES-FLOW ES Series Скачать руководство пользователя

Страница: 40 / 55

Bronkhorst®

Instruction Manual ES-FLOW™

9.17.145E

Counter Value

Type

Access

Range

FlowDDE

FLOW-BUS

Modbus

Float

0…

10000000

122

104/1

0xE808…0xE809/59401…59402

Current counter value in units selected with parameter

Counter Unit

Counter Limit

Type

Access

Range

FlowDDE

FLOW-BUS

Modbus

Float

0…9999999

124

104/3

0xE818…0xE819/59417…59418

Counter limit/batch size in units selected with parameter

Counter Unit

Default value: 0.

Counter Setpoint Mode

Type

Access

Range

FlowDDE

FLOW-BUS

Modbus

Unsigned char

0…1

126

104/5

0x0D05/3334

Specifies whether or not to change the setpoint after reaching the counter limit.

Value

Description

No setpoint change (default)

Change setpoint to

Counter new setpoint

Counter New Setpoint

Type

Access

Range

FlowDDE

FLOW-BUS

Modbus

Unsigned int

0…32000

127

104/6

0x0D06/3335

New (safe) setpoint when a counter limit is reached until reset. Range 0…32000 represents 0…100% setpoint.

Default value: 0

Reset Counter Enable

Type

Access

Range

FlowDDE

FLOW-BUS

Modbus

Unsigned char

0…15

157

104/9

0x0D09/3338

Available reset methods for counters. Up to 3 different methods can be specified. The value is a bitwise summation of the

enabled reset methods; convert the value to binary to see which methods are enabled.

Default value: 7 (bits/methods 0, 1 and 2 enabled)

The following methods are supported:

Bit

Value

Description

Micro-switch

Externally

By parameter

Reset

Automatically (e.g. when counter value is reset)

Totalizer Unit

Type

Access

Range

FlowDDE

FLOW-BUS

Modbus

Unsigned char[4]

See

Counter

Unit

394

104/18

0xE890…0xE891/59537…59538

This parameter contains the name of the totalizer readout unit.

Содержание ES-FLOW ES Series
























































Результаты поиска

Содержание ES-FLOW ES Series

Отзывы:

Похожие инструкции для ES-FLOW ES Series

Бренды по названию

Популярные бренды

BRONKHORST ES-FLOW ES Series, Инструкция по эксплуатации

Результаты поиска

Содержание ES-FLOW ES Series

Отзывы:

Похожие инструкции для ES-FLOW ES Series

Бренды по названию

Популярные бренды