BRONKHORST ES-FLOW ES Series Скачать руководство пользователя

Страница: 37 / 55

Bronkhorst®

Instruction Manual ES-FLOW™

9.17.145E

Analog Input

Type

Access

Range

FlowDDE

FLOW-BUS

Modbus

Unsigned int

0…65535

1/3

0x0023/36

This parameter contains a digital translation of the analog input signal (if applicable).

Valve Output

Type

Access

Range

FlowDDE

FLOW-BUS

Modbus

Unsigned long

0…

16777215

114/1

0xF208…0xF209/61961…61962

This parameter represents the controller output signal for control valve operation.

3.4.3

Alarms

Alarm settings are most easily accessible using FlowPlot or FlowView or a Bronkhorst® readout and control unit.

The built-in alarm functionality can be used to handle different alarm types:

system errors and warnings

min/max alarms

response alarms

batch alarms

master/slave alarms

The used alarm type can be set with parameter

Alarm Mode

. When an alarm is activated, the type can be read out using

parameter

Alarm Info

. An automatic setpoint change can be set using the parameters

Alarm Setpoint Mode

and

Alarm New

Setpoint

. It is also possible to set an alarm delay, to prevent overreaction to small disturbances, using parameter

Alarm Delay

Time

. The methods by which an alarm can be reset are controlled by

Reset Alarm Enable

Alarm Mode

Type

Access

Range

FlowDDE

FLOW-BUS

Modbus

Unsigned char

0…3

118

97/3

0x0C23/3108

Available modes:

Value

Description

Alarm off

Alarm on absolute limits

Alarm on limits related to setpoint (response alarm)

Alarm at power-up(e.g. after power-down)

(On DeviceNet™ instruments, only modes 0 and 1 are available)

Содержание ES-FLOW ES Series
























































Результаты поиска

Содержание ES-FLOW ES Series

Отзывы:

Похожие инструкции для ES-FLOW ES Series

Бренды по названию

Популярные бренды

BRONKHORST ES-FLOW ES Series, Инструкция по эксплуатации

Результаты поиска

Содержание ES-FLOW ES Series

Отзывы:

Похожие инструкции для ES-FLOW ES Series

Бренды по названию

Популярные бренды