BRONKHORST ES-FLOW ES Series Скачать руководство пользователя

Страница: 21 / 55

Bronkhorst®

Instruction Manual ES-FLOW™

9.17.145E

In the

Readout

sub menu, the following parameters can be edited:

Parameter

Description

Supported values

Readout format

Display format of measured value in main screen

actual

percentage

Type*

Measurement type

Note: value 'mass' can only be selected if parameter

Density

volume

mass

Unit*

Measurement unit

Depending on selected

measurement type

Fluid

Selected (metered) fluid

As ordered

Capacity

Maximum readout/control value (100%) for selected fluid

As ordered

Density*

Density of the selected fluid in kg/m

Note:

this is a fixed reference value, which is used to

calculate mass flows

0.000…99999.999

*) Not available on ES-FLOW models before Mk II.

3.3.3.2

Controller

The

Controller

sub menu is only available if the control function of the instrument is enabled. This setting is part of the

instrument configuration at the factory.

The control characteristics are optimized during production. These parameters should only be changed if absolutely

necessary, and only by or under the supervision of trained service personnel.

In the

Controller

sub menu, the following parameters can be edited:

Parameter

Description

Supported values

Speed

Controller speed factor

0.001…99.999

Slope

Controller adjustment speed

0.0…3000.0 seconds

Mode*

Control mode

see table below

Pid-Kp

PID controller proportional action

Pid-Ti

PID controller integration action

Pid-Td

PID controller differentiation action

Open from zero

Open from zero response

0…255

Normal step

Normal step response

0…255

Stable situation

Stable situation response

0…255

Master node*

Node address of master instrument

0…128

Slave factor**

Percentage of measurement value of master instrument

0…100.0%

Содержание ES-FLOW ES Series
























































Результаты поиска

Содержание ES-FLOW ES Series

Отзывы:

Похожие инструкции для ES-FLOW ES Series

Бренды по названию

Популярные бренды

BRONKHORST ES-FLOW ES Series, Инструкция по эксплуатации

Результаты поиска

Содержание ES-FLOW ES Series

Отзывы:

Похожие инструкции для ES-FLOW ES Series

Бренды по названию

Популярные бренды