BRONKHORST ES-FLOW ES Series Скачать руководство пользователя

Страница: 10 / 55

Bronkhorst®

Instruction Manual ES-FLOW™

9.17.145E

1.5.1

Customized I/O options

ES-FLOW™

instruments offer various customized input/output functions through pin 5 of the M12 connector and through

pin 2 of the M8 connector as an option. I/O options are factory installed as specified at ordering time, and cannot be

changed manually.

The last 3 groups of the model key on the serial number label indicate the installed I/O configuration. The possible

configurations are described in the table below. See the hook-up diagram for custom bus and I/O configurations

(document 9.16.196) for an explanation of the codes.

Code

Description

000

Disabled, pin 5 is pulled down to 0 Vdc (default selection)

A1V*

0…10 Vdc sourcing output, controller

Analog signal for pump or external valve steering (control signal only)

When the controller output is used for pump or external valve steering (mass flow meters only), make sure

to set parameter

Valve maximum

to 0.3 [A]. For mass flow controllers, the controller output is limited to a

value below 10Vdc, due to the maximum valve current restriction.

B1V*

4…20 mA sourcing output, controller

Analog signal for pump or external valve steering (control signal only).

When the controller output is used for pump or external valve steering (mass flow meters only), make sure

to set parameter

Valve maximum

to 0.3 [A]. For mass flow controllers, the controller output is limited to a

value below 20 mA, due to the maximum valve current restriction.

B2V*

3.8…20.8 mA sourcing output, controller

Analog signal for Badger Meter valve with TEIP11 signal converter (control signal only)

C3A

Digital output, min/max alarm

During a min/max alarm, pin 5 is pulled down to 0 Vdc.

C4A

Digital output, counter alarm

During a counter alarm, pin 5 is pulled down to 0 Vdc.

C5S

Digital output, enabled by setpoint (for shut-off control)

Pin 5 is pulled down to 0 Vdc at a controller setpoint, e.g. for shut-off valve activation.

For factory selected analog control (…-A#-C5S):

If parameter

Control mode

is set for analog control by factory, the minimum setpoint at which the device

(shut-off valve) connected to pin 5 is activated is 1.9%. This prevents possible noise on the analog input

activating the device accidentally.

For factory selected digital control (…-D#-C5S):

If parameter

Control mode

is set for digital control by factory, the setpoint threshold for activating the

device connected to pin 5 is any value > 0.

Note: If the instrument is forced into Valve Safe State, the digital output is not affected, so a (n.c.) shut-off

valve connected to pin 5 will not close when the (n.c.) controller is in Valve Safe State’

Make sure to use 24 Vdc power supply corresponding to the shut-off valve specifications.

C0I

Digital output, high/low switch via remote parameter (e.g. for shut-off valve control)

Pin 5 is pulled down to 0 Vdc when writing value 1 to parameter

IO switch status

, this is undone by writing

value 0.

A device connected to pin5 (e.g. a shut-off valve) can be activated/deactivated by writing parameter

switch status

Note: If the instrument is forced into Valve Safe State, the digital output is also affected, so a (n.c.) shut-off

valve connected to pin 5 will be closed when the (n.c.) controller is in ‘Valve Safe State’.

Make sure to use 24 Vdc power supply corresponding to the shut-off valve specifications.

Содержание ES-FLOW ES Series
























































Результаты поиска

Содержание ES-FLOW ES Series

Отзывы:

Похожие инструкции для ES-FLOW ES Series

Бренды по названию

Популярные бренды

BRONKHORST ES-FLOW ES Series, Инструкция по эксплуатации

Результаты поиска

Содержание ES-FLOW ES Series

Отзывы:

Похожие инструкции для ES-FLOW ES Series

Бренды по названию

Популярные бренды