BRONKHORST EL-PRESS Metal sealed Скачать руководство пользователя

Страница: 37 / 45

Bronkhorst®

Instruction Manual EL-PRESS™

9.17.101I

Alarm Setpoint Mode

Type

Access

Range

FlowDDE

FLOW-BUS

Modbus

Unsigned char

0…1

120

97/5

0x0C25/3110

Specifies whether or not to change the setpoint after an alarm situation is activated.

Value

Description

No setpoint change (default)

Change setpoint to

Alarm new setpoint

Alarm New Setpoint

Type

Access

Range

FlowDDE

FLOW-BUS

Modbus

Unsigned int

0…32000

121

97/6

0x0C26/3111

New (safe) setpoint during an alarm until reset. Range 0…32000 represents 0…100% setpoint.

Default value: 0

Reset Alarm Enable

Type

Access

Range

FlowDDE

FLOW-BUS

Modbus

Unsigned char

0…15

156

97/9

0x0C29/3114

Available reset methods for alarms. Up to 4 different methods can be specified; convert the value to binary to see which

methods are enabled.

Default value: 15 (all bits/methods enabled)

The following methods are supported:

Bit

Value

Description

Multifunctional switch

Externally (deprecated)

By parameter

Reset

Automatically (when alarm conditions no longer apply)

4.5

Network configuration

Changes made to the network settings will

not

be restored by a factory reset.

Содержание EL-PRESS Metal sealed














































Результаты поиска

Содержание EL-PRESS Metal sealed

Отзывы:

Похожие инструкции для EL-PRESS Metal sealed

Бренды по названию

Популярные бренды

BRONKHORST EL-PRESS Metal sealed, Инструкция по эксплуатации

Результаты поиска

Содержание EL-PRESS Metal sealed

Отзывы:

Похожие инструкции для EL-PRESS Metal sealed

Бренды по названию

Популярные бренды