Brocade Communications Systems ICX 7250 Скачать руководство пользователя страница 101

Страница: 101 / 119

Brocade ICX 7250 Switch Technical

Specifications

This content highlights the features and specifications for the Brocade ICX 7250 switch.

System specifications

System component

Description

Enclosure

1U; 19-inch rack-mountable; desktop- or wall-mountable

Power inlet

C14 for AC power

Custom connector for DC power from EPS4000 (not available on the ICX 7250-24G)

Power supplies

Integrated AC power supply for system and PoE power

External AC power supply (EPS4000) for redundant system power and extended PoE/PoE+ power (not
applicable to the ICX 7250-24G). DC power supplied to the switches depends on the EPS4000 configuration.

Fans

ICX 7250-24G: One fan per device

ICX 7250-24 : One fan per device

ICX 7250-24P: Two fans per device

ICX 7250-48: Two fans per device

ICX 7250-48P: Three fans per device

Cooling

Forced air circulation

ICX 7250-24G: front-to-back airflow

All other models: sides-to-back airflow

System architecture

Edge Ethernet switches

ICX 7250-24G: SFP uplink ports

ICX 7250-24, ICX 7250-24P, ICX 7250-48, ICX 7250-48P: SFP+ uplink and stacking ports

ICX 7250-24P, ICX 7250-48P: PoE/PoE+ ports

Ethernet

System component

Description

Ethernet ports

ICX 7250-24G: 24 RJ-45 GbE, 4 SFP GbE

ICX 7250-24: 24 RJ-45 GbE, 8 SFP+ 10 GbE

ICX 7250-24P: 24 RJ-45 GbE with PoE/PoE+, 8 SFP+ 10 GbE

ICX 7250-48: 48 RJ-45 GbE, 8 SFP+ 10 GbE

ICX 7250-48P: 48 RJ-45 GbE with PoE/PoE+, 8 SFP+ 10 GbE

Management interface

One 10/100/1000 Ethernet, out-of-band management interface (RJ-45 port)

Brocade ICX 7250 Switch Hardware Installation Guide

53-1003898-02

101

Содержание ICX 7250
























































































































Результаты поиска

Содержание ICX 7250

Отзывы:

Похожие инструкции для ICX 7250

Бренды по названию

Популярные бренды

Brocade Communications Systems ICX 7250, Руководство по установке оборудования

Результаты поиска

Содержание ICX 7250

Отзывы:

Похожие инструкции для ICX 7250

Бренды по названию

Популярные бренды