Brocade Communications Systems ICX 7250 Скачать руководство пользователя страница 100 | Manualshive

Страница: 100 / 119

Brocade Communications Systems ICX 7250 Скачать руководство пользователя страница 100

Cleaning the fiber-optic connectors

To avoid problems with the connection between the fiber-optic transceiver (SFP or SFP+) and the fiber cable connectors, Brocade
strongly recommends cleaning both connectors each time you disconnect and reconnect them. Dust can accumulate in the connectors
and cause problems, such as reducing the optic launch power.

To clean the fiber cable connectors, Brocade recommends using a fiber-optic reel-type cleaner. When not using an SFP or SFP+
connector, make sure to keep the protective covering in place.

Cabling a fiber-optic transceiver

Perform the following steps to cable a fiber-optic transceiver.

1.

Remove the protective covering from the fiber-optic port connectors and store the covering for future use.

NOTE
Before cabling a fiber-optic transceiver, Brocade strongly recommends cleaning the cable connectors and the port
connectors.

2. Gently insert the cable connector (a tab on each connector should face upward) into the transceiver connector until the tabs lock

into place.

3. Observe the link and active LEDs to determine if the network connections are functioning properly. For more information about

the LED indicators, refer to

on page 89.

Hardware Maintenance Schedule

Brocade ICX 7250 Switch Hardware Installation Guide

100

53-1003898-02

«
...
98
99
100
101
102
...
»

Содержание ICX 7250
























































































































Отзывы:

Нет отзывов