Brocade Communications Systems DCX 8510-8 Скачать руководство пользователя страница 77

Страница: 77 / 176

Replacing a chassis door

Complete the following steps to reinstall the door.

1. Align the holes in the door with the ball studs on the chassis.
2. Push the door into place. It will snap onto the studs.

Cable management comb removal and replacement

The Brocade DCX 8510-8 can continue to operate during the replacement of the cable management
comb.

Time and items required

The replacement procedure for the cable management comb takes less than five minutes. A #1 Phillips
screwdriver is required.

Removing a cable management comb

Complete the following steps to remove the cable management comb.

1. Remove the chassis door.
2. Remove the cables from the cable management comb and rearrange the cables around the comb.
3. Unscrew and save the four (4) screws holding the comb to the chassis. Support the comb to prevent

it from falling.

4. Remove the cable management comb.

Replacing a chassis door

Brocade DCX 8510-8 Backbone Hardware Reference Manual

53-1002180-08

Содержание DCX 8510-8

















































































































































































Результаты поиска

Содержание DCX 8510-8

Отзывы:

Похожие инструкции для DCX 8510-8

Бренды по названию

Популярные бренды

Brocade Communications Systems DCX 8510-8, Справочник по аппаратуре

Результаты поиска

Содержание DCX 8510-8

Отзывы:

Похожие инструкции для DCX 8510-8

Бренды по названию

Популярные бренды