manualshive.com logo in svg

Brocade Communications Systems DCX 8510-8, Справочник по аппаратуре

Поделиться
Скачать
Brocade Communications Systems DCX 8510-8 Скачать руководство пользователя страница 47

NOTE

Refer to "Cabling Best Practices" (available at 

http://www.brocade.com

 ) for cable management

guidelines.

For the procedure to install the ICL cables, refer to 

Inter-chassis link (ICL) cable removal and

replacement

 on page 108

Verifying correct operation and backing up the configuration

To verify correct operation and back up the Brocade DCX 8510-8 configuration, follow these steps. For
information about LED patterns, refer to 

Determining the status of a port or application blade

 on page

54.

Complete the following steps to back up the configuration for the Brocade DCX 8510-8.

1. Check the LEDs to verify that all components are functional.
2. If necessary, log in to the switch by Telnet, using the 

admin

 account.

3. Verify the correct operation of the Brocade DCX 8510-8 by entering the 

switchShow

 command from

the workstation. This command provides information about switch and port status.

4. Verify the correct operation of the Brocade DCX 8510-8 in the fabric by entering the 

fabricShow

command from the workstation. This command provides general information about the fabric.

5. To back up the configuration, run the following two steps:

a)

Enter the 

configupload -vf 

command. This command uploads the Brocade DCX 8510-8

virtual fabric data.

b)

Enter the 

configupload

 command. This command uploads the Brocade DCX 8510-8

configuration.

6. You can run the following commands to see additional configuration information that you can copy to

a file to save:

•

configShow

•

ipaddrShow

•

licenseShow

•

switchShow

Alternatively, you can save the configuration file to a Brocade USB device by using the 

usbstorage

command.

NOTE

Passwords are not saved in the configuration file, and are not uploaded during a configuration
upload.

NOTE

It is recommended that the configuration be backed up on a regular basis to ensure that a complete
configuration is available for downloading to a replacement Brocade DCX 8510-8.

Verifying correct operation and backing up the configuration

Brocade DCX 8510-8 Backbone Hardware Reference Manual

47

53-1002180-08

Содержание DCX 8510-8

















































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды