manualshive.com logo in svg

Brocade Communications Systems DCX 8510-8, Справочник по аппаратуре

Поделиться
Скачать
Brocade Communications Systems DCX 8510-8 Скачать руководство пользователя страница 21

• DH-CHAP
• SSHv2 (using AES, 3DES, RSA)
• HTTPS (using AES)
• SNMPv3
• FC-SP
• Secure RPC
• Secure file copy (SCP)
• Telnet disable
• Telnet timeout
• IP filters (block listeners)
• Secure passwords (centralized control through RADIUS/CHAP)
• Multiple user accounts (MUAs) (Up to 255)
• Role-based access controls (RBACs)
• Administrative domains/Virtual fabrics
• Boot PROM password reset
• Password hardening policies
• Up front login in Web Tools
• Login banner
• Monitoring of attempted security breaches (through audit logging)
• Monitoring of attempted security breaches (through Fabric Watch Security Class)
• Fibre Channel security policies: DCC and SCC
• Trusted Switch (FCS) for central security management
• Management access controls (SNMPv3, Telnet, FTP, serial port, front panel)
• Hardware-enforced zoning by WWN, domain/port ID, or both
• Default zoning
• RSCN suppression and aggregation
• Configurable RSCN suppression by port
• NTPv3 (to synchronize timestamps)
• Event auditing
• Change tracking
• Firmware change alerts in Fabric Manager
• Persistent port disable
• Persistent domain ID
• E_Port disable

Network manageability

The Brocade DCX 8510-8 has a single domain and is managed as a single element with Brocade
Network Advisor. The Brocade DCX 8510-8 responds to its own IP address and appears as a separate
entity to the Telnet protocol and SNMP.

All management interfaces, such as Telnet, Web Tools, standards-compliant SMI-S, and Management
Server, support a "port N within blade M" naming scheme.

The Brocade DCX 8510-8 supports SNMPv1 and SNMPv3. When SNMP devices send SNMP
messages to a management console running SAN management software, the information is stored in a
management information base (MIB). Fabric OS v7.0.0 and later supports the latest Fibre Alliance Fibre
Channel Management (FCMGMT) and Storage Management Initiative (SMI) MIBs, which allow
common information necessary for management software to provide information to a SAN
administrator. Refer to the 

Fabric OS MIB Reference

 for additional MIB information.

Network manageability

Brocade DCX 8510-8 Backbone Hardware Reference Manual

21

53-1002180-08

Содержание DCX 8510-8

















































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды