manualshive.com logo in svg

Brocade Communications Systems DCX 8510-8, Справочник по аппаратуре

Поделиться
Скачать
Brocade Communications Systems DCX 8510-8 Скачать руководство пользователя страница 150

Power-cord notice (Japan, Denan)

DANGER
Never use the power cord packed with your equipment for other products.

BSMI statement (Taiwan)

Warning:

This is Class A product. In a domestic environment, this product may cause radio interference, in
which case the user may be required to take adequate measures.

CE statement

This is a Class A product. In a domestic environment, this product might cause radio interference, and
the user might be required to take corrective measures.

The standards compliance label on the product contains the CE mark which indicates that this system
conforms to the provisions of the following European Council directives, laws, and standards:

• Electromagnetic Compatibility (EMC) Directive 2004/108EEC
• Low Voltage Directive (LVD) 73/23/EEC and the Complementary Directive 93/68/EEC
• EN55022:2006 (European Emissions Requirements)
• EN55024:1998, +A1:2001 and +A2:2003 (European Immunity Requirements)
• EN61000-3-2:2006/JEIDA (European and Japanese Harmonics Spec)
• EN61000-3-3:1995, +A1:2001 and +A2:2005

Power-cord notice (Japan, Denan)

150

Brocade DCX 8510-8 Backbone Hardware Reference Manual

53-1002180-08

Содержание DCX 8510-8

















































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды