Broan VB0310 Скачать руководство пользователя страница 4 | Manualshive

Страница: 4 / 24

Broan VB0310 Скачать руководство пользователя страница 4

4

1. T

YPICAL

I

NSTALLATIONS

Use the following illustrations as guidelines to help you decide on how the unit will be installed.
All the units should be hung from the joists.
In every case, bathroom fans and a range hood could be used to exhaust stale air. However, please note that an optional bathroom
installation kit (no. IKBV1000 for Venmar units and no. IKBB1000 for Broan units) is available for house where there is no bathroom fans.
Also, for homes with more than one level, we recommend one exhaust register at the highest level.
There are 3 installation methods: Fully Ducted System, Central Draw Point and Simplified Installation.

NOTE: An electrical outlet has to be available within 3 feet of the unit.

1.1 F

ULLY

D

UCTED

S

YSTEM

(P

RIMARILY

FOR

HOMES

WITH

RADIANT

HOT

WATER

OR

ELECTRIC

BASEBOARD

HEATING

)

VH0088

Stale air coming from the register located at the highest level of the
house is exhausted to the outside. Fresh air from outside is filtered and
supplied by the register located in the lowest liveable level.
Homes with more than one level require at least one exhaust register at
the highest level.
See figure at right.

1.2 C

ENTRAL

D

RAW

P

OINT

(C

ONNECTION

TO

A

FORCED

AIR

SYSTEM

)

VH0089

Stale air coming from the register located at the highest level of the
house is exhausted to the outside. Fresh air from outside is filtered and
supplied to the return (plenum) or the supply duct of the forced air unit.
See figure at right.
For this type of installation, it is not essential that the forced air system
blower runs when the unit is in operation, but we recommend it.
NOTE: Home with multiple forced air systems should have one unit on
each

system.

1.3 S

IMPLIFIED

I

NSTALLATION

(C

ONNECTION

TO

A

FORCED

AIR

SYSTEM

)

VH0090

Stale air is exhausted to the outside. Fresh air from outside is filtered and
supplied to the return (plenum) or the supply duct of the forced air unit.
See figure at right.
To avoid cross-contamination and achieve the highest efficiencies, the
forced air system blower must always be ON.
NOTE: Home with multiple forced air systems should have one unit on
each

system.

Do not connect the unit to any forced air system supply
duct.

CAUTION

Do not connect the unit to any forced air system supply
duct.

CAUTION

«
...
2
3
4
5
6
...
»

Содержание VB0310

























Отзывы:

Нет отзывов