Broadcom NetXtreme BCM57 Series Скачать руководство пользователя | Manualshive

Страница: 151 / 174

background image

iSCSI Protocol and Broadcom Boot Agent Software

NetXtreme

User Guide

Broadcom

®

April 2017 • 2CS57XX-CDUM514-R

Page 151

14.

After Windows 2012 boots to the OS, Broadcom recommends running the driver installer to complete the
Broadcom driver and application installation.

Linux iSCSI Boot Setup

Linux iSCSI boot is supported on Red Hat Enterprise Linux 6.9, 7.1 and later and SUSE Linux Enterprise Server
(SLES) 11 SP4, or SLES 12 SP2 and later.

1.

For driver update, obtain the latest Broadcom Linux driver CD.

2.

Configure the iSCSI Boot Parameters for DVD direct install to target by disabling the Boot from target option
on the network adapter.

3.

Change the boot order as follows:
a. Boot from the network adapter.
b. Boot from the CD/DVD driver.

4.

Reboot the system.

5.

System will connect to iSCSI target, then will boot from CD/DVD drive.

6.

Follow the corresponding OS instructions.
a. RHEL 6.9 — Type “linux dd” at “boot:” prompt and press enter
b. SuSE 11.X — Choose

installation

and type

withiscsi=1 netsetup=1

at the boot option. If driver update

is desired, choose

YES

for the F6 driver option.

7.

If driver update is desired, follow the instructions to load the driver CD; otherwise skip this step.

8.

At the “networking device” prompt, choose the desired network adapter port and press

OK

.

9.

At “configure TCP/IP prompt”, configure the way the system acquire IP address and press

OK

.

10.

If static IP was chosen, you need to enter IP information for iscsi initiator.

11.

(RHEL) Choose to “skip” media testing.

12.

Continue installation as desired. A drive will be available at this point. After file copying is done, remove CD/
DVD and reboot the system.

13.

When the system reboots, enable “boot from target” in iSCSI Boot Parameters and continue with installation
until it is done.

At this stage, the initial installation phase is complete. The rest of the procedure pertains to creating a new
customized initrd for any new components update:

14.

Update iscsi initiator if desired. You will first need to remove the existing initiator using

rpm -e

.

15.

Make sure all runlevels of network service are on:

chkconfig network on

16.

Make sure 2,3 and 5 runlevels of iscsi service are on.

chkconfig -level 235 iscsi on

17.

For Red Hat 6.0, make sure Network Manager service is stopped and disabled.

18.

Install iscsiuio if desired (not required for SuSE 10).

19.

Install linux-nx2 package if desired.

«
...
149
150
151
152
153
...
»

Содержание NetXtreme BCM57 Series















































































































































































Отзывы:

Нет отзывов

Похожие инструкции для NetXtreme BCM57 Series

Бренд: Gardena Страницы: 100

Бренд: IBM Страницы: 72

Бренд: Magnescale Страницы: 132

Бренд: Access Страницы: 12

Бренд: Samson Страницы: 20

Бренд: Rain Bird Страницы: 138

Бренд: Xantrex Страницы: 56

Бренд: Xantrex Страницы: 2

Freedom Sequence

Бренд: Xantrex Страницы: 58

Бренд: Xantrex Страницы: 4

Бренд: Xantrex Страницы: 20

Бренд: IBM Страницы: 20

Бренд: DAV TECH Страницы: 24

Бренд: OBSIDIAN CONTROL SYSTEMS Страницы: 16

Бренд: Watts Страницы: 17

Centronic SunWindControl SWC245-II

Бренд: Becker Страницы: 52

Бренд: Apex Toys Страницы: 7

Бренд: 2N Страницы: 107

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды