Broadcom Brocade G720 Скачать руководство пользователя страница 44 | Manualshive

Страница: 44 / 86

background image

G720-Install-IG101 Installation Guide

Brocade

®

G720 Switch Hardware Installation Guide

Attaching the Rear Brackets to the Rack

Complete the following steps to attach the rear brackets to the rack.
1. Select the proper length bracket for your post width. If your posts are 3 in. to 5 in. wide, use the brackets marked 3-5

INCH. If your posts are 5 in. to 6 in. wide, use the brackets marked 5-6 INCH.

2. Position the right rear bracket in the right rear of the device, as shown in the figure. Whether you are using the 3-5

INCH or the 5-6 INCH bracket, the rear end of the bracket will be flush with the back of the device.

3. Attach the brackets to the right rack upright using two 10-32 x 5/8-in. panhead screws and two retainer nuts.
4. Repeat Step 2 and Step 3 to attach the left rear bracket to the left rack upright.
5. Tighten all 10-32 x 5/8-in. screws to a torque of 29 cm-kg (25 in.-lb).

Figure 22: Attaching the Rear Brackets to the Rack

1. Retainer Nuts, 10-32

2. Rear Brackets (Right and Left)

3. Screws, 10-32 x 5/8-in. Panhead Phillips

G720-Install-IG101

44

Broadcom

«
...
42
43
44
45
46
...
»

Содержание Brocade G720























































































Отзывы:

Нет отзывов

Похожие инструкции для Brocade G720

DES-3224 - Switch

Бренд: D-Link Страницы: 75

VH M 1 1 1 Series

Бренд: Jlso Tec Trade Страницы: 15

Бренд: Cypress Страницы: 16

Бренд: TRENDnet Страницы: 2

CESRA PIR 10VDC

Бренд: DANLERS Страницы: 2

Бренд: Zektor Страницы: 30

Бренд: Generac Power Systems Страницы: 2

OSD2251P Series

Бренд: Optical Systems Design Страницы: 48

Бренд: Link Страницы: 35

GTB-MHDMI1.3-442

Бренд: Gefen Страницы: 29

Бренд: Thinklogical Страницы: 45

Allen-Bradley Guardmaster 440G-LZ

Бренд: Rockwell Automation Страницы: 40

Бренд: Kramer Страницы: 39

Бренд: Efapel Страницы: 44

Бренд: Tripp Lite Страницы: 12

Бренд: PS Automation Страницы: 4

Бренд: Hirschmann Страницы: 50

Бренд: Kramer Страницы: 31

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды