manualshive.com logo in svg

Broadcom BCM1125, Руководство пользователя

Broadcom BCM1125 - высокопроизводительный процессор, обеспечивающий быструю и эффективную работу устройства. Чтобы ознакомиться с руководством пользователя, вы можете бесплатно скачать его с нашего сайта. Узнайте больше о вашем устройстве, загрузив руководство по эксплуатации на manualshive.com.

Поделиться
Скачать
background image

BCM1250/BCM1125/BCM1125H

User Manual

10/21/02

B r o a d c o m   C o r p o r a t i o n

Page  

48

Section 4: System Control and Debug Unit

 Document

1250_1125-UM100CB-R

To assist software dispatch there are status registers associated with each of the six CPU interrupt lines, DINT
and the NMI. These indicate which sources are interrupting, pass the mask and are routed to this interrupt line.
In addition there is a global status register that shows which sources are interrupting regardless of their mask
setting or routing. 

The debug interrupt (DINT) to the CPU may be raised by the interrupt mapper. It will also be raised if a trace
trigger is marked to send DINT (see 

Section: “Trigger Sequences” on page 73

) or if the break control bit is set

in the EJTAG control register (see 

Section: “EJTAG Control Register” on page 440

).

There is a diagnostic register built into the interrupt mapper that can be used to force interrupts to be asserted
into the mask and map logic. 

Since there is a full copy of the mapper for each CPU, system interrupts may be masked and mapped
differently on the two processors. In many cases a particular source would always be assigned to a particular
processor, delivering it to both requires software to coordinate servicing the interrupt. 

H

YPER

T

RANSPORT

 I

NTERRUPTS

The HyperTransport bus protocol includes passing interrupt messages across the HyperTransport fabric.
These messages include identification of the interrupt vector (as described below there are some non-vectored
interrupts, carrying meanings specific to the x86 architecture, but these are thought of as having an implicit
vector number in the interrupt mapper). The MIPS architecture does not directly support hardware interrupt
vectoring, so the vector number is used by the hardware to decide which input to the interrupt mapper will be
triggered and software can do any required vectoring. 

The interrupt packet also includes a destination. This is either a physical processor number or "a system
specific logical mapping". The BCM1250 CPUs (and their related interrupt controllers) are physically numbered
0 and 1. The BCM1125H CPU (and interrupt controller) is physical number 0. The logical mapping used is the
example one from the HyperTransport specification, a processor is selected as the target by setting the bit
position corresponding to its physical processor number. This scheme allows for up to eight processors. Use
of the logical mapping allows broadcast and multicast interrupts (having only two CPUs, these amount to the
same thing on the BCM1250). The mapper supports the 8 bit destination from the HyperTransport
Specification rev 1.0 and earlier, and will ignore the additional 24 destination bits added by the HyperTransport
Specification rev 1.01.

The HyperTransport interrupt messages must maintain ordering with transactions that come across the
HyperTransport link ahead of them. They therefore follow the same flow as other HyperTransport transactions
and are delivered to the SCD across the ZBbus as writes to the 

interrupt_ldt_set

 register. Writes to this

register are decoded and used to set bits in either the 

mailbox

 register or the 

interrupt_ldt

 register. The CPU

can write the 

interrupt_ldt_set

 register during testing to simulate the arrival of an interrupt message. The data

written is a 64-bit double-word containing the data from the HyperTransport Interrupt message as described in

Table 19

. 

Содержание BCM1125





































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для BCM1125

3Com 3C16080 Important Information preview
3C16080
Бренд: 3Com Страницы: 2
3Com 3C421600A Quick Setup Manual preview
3C421600A
Бренд: 3Com Страницы: 74
3Com 3C421600A Installation Manual preview
3C421600A
Бренд: 3Com Страницы: 6
Paradyne MCC Installation Instructions Manual preview
MCC
Бренд: Paradyne Страницы: 11
Paradyne Hotwire 8784 Installation Instructions Manual preview
Hotwire 8784
Бренд: Paradyne Страницы: 19
Paradyne COMSPHERE 3550 Series User Manual preview
COMSPHERE 3550 Series
Бренд: Paradyne Страницы: 153
Paradyne Jetstream CPX-1000 Reference Manual preview
Jetstream CPX-1000
Бренд: Paradyne Страницы: 141
Patton electronics 1084 Installation And Operation Manual preview
1084
Бренд: Patton electronics Страницы: 16
Omega Engineering OME-A8111 Hardware Manual preview
OME-A8111
Бренд: Omega Engineering Страницы: 34
XNET INS2000 Install Manual preview
INS2000
Бренд: XNET Страницы: 17
EK EK-Quantum Momentum ROG Rampage VI Encore User Manual preview
EK-Quantum Momentum ROG Rampage VI Encore
Бренд: EK Страницы: 11
Marani LPP-440A User Manual preview
LPP-440A
Бренд: Marani Страницы: 39
Aaeon FWS-7150 Manual preview
FWS-7150
Бренд: Aaeon Страницы: 57
Juniper NSM4000 Hardware Manual preview
NSM4000
Бренд: Juniper Страницы: 196
Extron electronics VERSATOOLS MTP User Manual preview
VERSATOOLS MTP
Бренд: Extron electronics Страницы: 19
audemat DIGIPLEXER 246 User Manual preview
DIGIPLEXER 246
Бренд: audemat Страницы: 93
ICP DAS USA VXC-114U Series Quick Start Manual For preview
VXC-114U Series
Бренд: ICP DAS USA Страницы: 8
ADLINK Technology ROScube-I Series User Manual preview
ROScube-I Series
Бренд: ADLINK Technology Страницы: 95

Бренды по названию

Популярные бренды

Загрузить еще бренды