Broadcom BCM1125 Скачать руководство пользователя страница 385 | Manualshive

Страница: 385 / 516

background image

User Manual

BCM1250/BCM1125/BCM1125H

10/21/02

B r o a d c o m C o r p o r a t i o n

Document

1250_1125-UM100CB-R

Section 10: Serial Interfaces Page

357

18

rx_eop_seen

Set at the end of any packet transfer. It can be used during polling to determine if any
packets have been transferred since the register was read (regardless of the setting of
the int_pktcnt field).

19

rx_hwm

Set if the high watermark interrupt is raised.

20

rx_lwm

Set if the low watermark interrupt is raised.

21

rx_dscr

Set if the interrupt is triggered by a descriptor with the interrupt on packet end command.

22

rx_derr

Set if the controller ran out of descriptors during a packet reception. The channel will be
stopped. Software must disable and re-enable the channel to clear this fault.

23

reserved

Reserved

24

tx_eop_count

Set if the EOP interrupt was raised as a result of the packet count being reached.

25

tx_eop_timer

Set if the EOP interrupt was raised as a result of the packet timer triggered.

26

tx_eop_seen

Set at the end of any packet transfer. It can be used during polling to determine if any
packets have been transferred since the register was read (regardless of the setting of
the int_pktcnt field).

27

tx_hwm

Set if the high watermark interrupt is raised.

28

tx_lwm

Set if the low watermark interrupt is raised.

29

tx_dscr

Set if the interrupt is triggered by a descriptor with the interrupt on packet end command.

30

tx_derr

Set if the controller ran out of descriptors during a packet transmission. The channel will
be stopped. Software must disable and re-enable the channel to clear this fault.

31

tx_dzero

Set if a descriptor has a packet length of zero. The channel will be stopped. Software
must disable and re-enable the channel to clear this fault.

63:32

notimp

Not implemented.

Table 240: Synchronous Serial Status Register

(Cont.)

ser_status_0 -

00_1006_0588

ser_status_1 -

00_1006_0988

READ ONLY, Read Clears

Bits

Name

Description

Table 241: Serial Status Debug Register

ser_status_debug_0 -

00_1006_05A8

ser_status_debug_1 -

00_1006_09A8

Bits

Name

Default

Description

31:0

status

32’b0

Reading this register gives the same value as reading the

ser_status

register, but does

not have the side effect of clearing the register.

63:32

notimp

32’bx

Not implemented.

Table 242: Serial Interrupt Mask Register

ser_int_mask_0 -

00_1006_0590

ser_int_mask_1 -

00_1006_0990

Bits

Name

Default

Description

31:0

mask

32’b0

Setting a bit in this register enables generation of an interrupt when the corresponding
status bit is set in the

ser_status

register.

63:32

notimp

32’bx

Not implemented.

«
...
383
384
385
386
387
...
»

Содержание BCM1125





































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для BCM1125

Бренд: dbx Страницы: 8

Бренд: Paradyne Страницы: 16

Бренд: Blackrock Microsystems Страницы: 27

Бренд: Analog Devices Страницы: 76

Бренд: Digitus Страницы: 8

iTRON B 70.2040

Бренд: JUMO Страницы: 41

Digital Encoder Plus

Бренд: IDT Страницы: 98

Бренд: AOpen Страницы: 18

Бренд: Microchip Technology Страницы: 9

E5345 - Xeon 2.33 GHz 8M L2 Cache 1333MHz FSB LGA771 Active Quad-Core Processor

Бренд: Intel Страницы: 112

J-Link-OB-STM32F072-128KB

Бренд: Segger Страницы: 18

CHEETAH ST34501FC

Бренд: Seagate Страницы: 68

Бренд: Advantech Страницы: 66

Бренд: COUGAR Страницы: 2

Бренд: Cutting Edge Страницы: 92

Vortex86SX VSX-6101

Бренд: ICOP Technology Страницы: 50

Бренд: JCAT Страницы: 2

Бренд: Jäger Страницы: 54

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды