manualshive.com logo in svg

Broadcom BCM1125, Руководство пользователя

Broadcom BCM1125 - высокопроизводительный процессор, обеспечивающий быструю и эффективную работу устройства. Чтобы ознакомиться с руководством пользователя, вы можете бесплатно скачать его с нашего сайта. Узнайте больше о вашем устройстве, загрузив руководство по эксплуатации на manualshive.com.

Поделиться
Скачать
background image

BCM1250/BCM1125/BCM1125H

User Manual

10/21/02

B r o a d c o m   C o r p o r a t i o n

Page  

240

Section 8: PCI Bus and HyperTransport Fabric

 Document

1250_1125-UM100CB-R

11

SigdTgtAbort R/C

0’b0

This bit is set when the bridge is the target of a PCI transaction and signalled a 
Target Abort. If this bit is set the PCI error interrupt is asserted. It is cleared by 
software writing a 1.

12

RcvdTgtAbort

R/C 1’b0

This bit is set when the bridge was a master for a transaction and received a Target 
Abort. If this bit is set the PCI error interrupt is asserted. It is cleared by software 
writing a 1.

13

RcvdMstrAbort

R/C 1’b0

This bit is set when the bridge was a master for a transaction that was not a Special 
Cycle and signalled a Master Abort. If this bit is set the PCI error interrupt is asserted. 
It is cleared by software writing a 1.

14

SigdSerr

R/C 1’b0

This bit is set when the bridge asserts SERR_L. It will do this when it detects a parity 
error on an address. If this bit is set the PCI error interrupt is asserted. It is cleared 
by software writing a 1.

15

DetParErr

R/C 1’b0

This bit will be set whenever the bridge detects a parity error, even if parity error 
handling is disabled. The parity error is only signalled using the PCI interrupt if the 
ParErrResp bit is set in the command register. This bit is cleared by software writing 
a 1.

Table 129:  PCI Status Register - Offset 4 Bits [31:16]

 (Cont.)

Bits

Name

Default

Description

Table 130:  PCI Latency Timer - Offset 0C Bits [15:8]

Bits

Name

Default

Description

7:0

LatTime

R/W 8’b0

This contains the value of the Latency Timer for the bridge to use when bus master. If 
this register is left at its default value of zero the bridge will never do bursts on the PCI. 
Bits 1:0 are R/O and are always zero.

Table 131:  PCI Cache Line Size - Offset 0C Bits [7:0]

Bits

Name

Default

Description

7:0

ClineSz

R/W 8’h0

This register sets the cache line size in DWORDS (32 bit words) used by the bridge for 
PCI transactions. As a master the bridge bases the PCI command used on how the size 
of the transfer matches the value in this register:

word_count < one cacheline: use Read command

word_count >= one cacheline: use Read Line command
word_count >= two cache lines: use Read Multiple command.

This size is also used to enable the Write Invalidate command. 

Table 132:  PCI Timeout Register - Offset 40 Bits [15:0]

Bits

Name

Default

Description

7:0

TrdyTimeout

R/W 8’h80 This field sets the maximum number of PCI cycles that the bridge will wait for TRDY 

to be asserted. If TRDY is deasserted for longer than this the transfer will be 
aborted. When a transfer is aborted the TrdyErr bit is set in the Additional Status 
register and the pci_interrupt may be raised. If a read is aborted UNPREDICTABLE 
data is returned to the ZBbus marked with a bus error.

15:8

RetryTimeout

R/W 8’h80 This field sets the number of times a read will be retried following a disconnect. 

The read is first attempted this number of times. The bridge will then allow any 
outstanding writes and read-data-returns to proceed before retrying the read. In 
interface revisions less than 3 a second attempt is made, in revisions 3 and later 
the read is retried the number of times specified in the num_piowr_bypass field of 
the PCI Bypass Control register (

Table 139

). If the read fails on the final attempt the 

transfer is aborted, UNPREDICTABLE data marked with a bus error is returned to 
the ZBbus and the RetryErr bit is set in the Additional Status register.

A write that is retried will be attempted the number of times specified in this field 
before being discarded and the RetryErr bit set.

Содержание BCM1125





































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для BCM1125

Baracoda All in One Printer Communication Protocol Manual preview
All in One Printer
Бренд: Baracoda Страницы: 42
D-Link xStack Storage DSN-4000 Series Datasheet preview
xStack Storage DSN-4000 Series
Бренд: D-Link Страницы: 5
GE Mini Field Agent User Manual preview
Mini Field Agent
Бренд: GE Страницы: 87
Idis DR-4100P Series Installation Manual preview
DR-4100P Series
Бренд: Idis Страницы: 30
TC Electronic DB6 User Manual preview
DB6
Бренд: TC Electronic Страницы: 174
TC Electronic Finalizer Express User Manual preview
Finalizer Express
Бренд: TC Electronic Страницы: 33
Idis DR-6100 Series Operation Manual preview
DR-6100 Series
Бренд: Idis Страницы: 86
Paradyne COMSPHERE 3610 Installation Instructions preview
COMSPHERE 3610
Бренд: Paradyne Страницы: 2
LORD AP5103 Series Technical Manual preview
AP5103 Series
Бренд: LORD Страницы: 9
Longshine LCS-8131G3 User Manual preview
LCS-8131G3
Бренд: Longshine Страницы: 27
RANA Systems Elite Controller User Manual preview
Elite Controller
Бренд: RANA Systems Страницы: 328
Infoblox Trinzic 100 Installation Manual preview
Trinzic 100
Бренд: Infoblox Страницы: 13
Renesas H8S/2437 Hardware Manual preview
H8S/2437
Бренд: Renesas Страницы: 746
ICP DAS USA I-87K Series User Manual preview
I-87K Series
Бренд: ICP DAS USA Страницы: 31
Microcomputer Systems MSI-P602 User Manual preview
MSI-P602
Бренд: Microcomputer Systems Страницы: 21
Thermalright Macho Rev. A (BW) Manual preview
Macho Rev. A (BW)
Бренд: Thermalright Страницы: 32
CSI 7798 I/SITE LAN Installation Manual preview
7798 I/SITE LAN
Бренд: CSI Страницы: 56
National Instruments NI 653x User Manual preview
NI 653x
Бренд: National Instruments Страницы: 147

Бренды по названию

Популярные бренды

Загрузить еще бренды